Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included that match “1”►
- Honda
Piston Ring Set - 1st Oversize (0.25mm.)
1st Oversize Piston Ring Set + 0.25mm. Ring Set OEM Ref. # 13021-392-000 / 13021-392-004 Japanese made Superior Quality Note: This Set includes piston rings to rebuild one piston, 4 Sets are needed to rebuild all pistons.
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 5 1/8" Offset 1 3/8"
Oil Pump Rebuild Kit
11 Pc. Oil Pump Rebuild Kit. Use this kit to get your oil pump flowing at maximum capacity for a healthy engine, performing at it's best! Kit includes 1 oil stopper seal, 1 oil stopper spring, 1 oil relief valve spring, 1 oil relief valve o-ring, 3 pump connection o-rings, 2 inner rotor o-rings, 1 steel reinforced center shaft seal, 1 pump body gasket.
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Economy Engine Oil Seal Kit
7 pc. Engine Oil Seal Kit. 1 pc. 91205-405-005 / 91205-405-000 Countershaft sprocket oil seal - 30 x 62 x 7/8 1 pc. 91202-216-000 / 91202-302-010 Clutch arm seal - SB type - 13.8 x 24 x 5 1 pc. 91206-286-005 / 91206-286-013 / 91206-286-003 Shift shaft seal - 14 x 28 x 7 1 pc. 91201-300-003 Crank seal 30 x 42 x 8 1 pc. 91215-300-003 Seal - Starting clutch gear - 25 x 33 x 4 1 pc. 91204-286-003 / 91204-286-005 Kickstart Oil Seal 18 x 29 x 7 1 pc. 91211-286-003 Tach drive oil seal 4.8 x 14.5 x 4
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
CB Black Mirror - Original Type (Left Side)
Gloss Black CB Style Left Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
CB Black Mirror - Original Type (Right Side)
Gloss Black CB Style Right Side Mirror - 4 1/2" Diameter with 10mm. RH Thread & 7" Stems.
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-254-000 / 18291-MM5-860 Sold Each, Order the Quantity you Require
Exhaust Headpipe Gasket (Each)
Cylinder Head to Exhaust Headpipe Gasket (1 Pc.) OEM Ref. # 18291-MM5-860 Sold Each, Order the Quantity you Require
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Handlebar - Stock Type ~ CB750K 1977-78
Stock Type Handlebar for the CB750K (1977-78) - Chrome. Bars are not drilled for wires. Bar Diameter - 7/8" - 22mm, Length - 31" - 787mm, Pull Back - 5 1/4" - 133mm, Inner Rise - 7" - 178mm, End Rise - 9" - 228mm, Center Width - 6" - 152mm, Base Width - 9 1/2" - 241mm, Knurl Width - 4 1/2" - 114mm, Control Length - 8 1/2" - 216mm, Drilled - YES Replaces OEM # 53100-405-010
Fork Leg Washer Set
Fork Leg Copper Washer Set (4) 8mm x 13mm x 1.5mm x 2pcs (OEM Ref 90544-283-000) 6mm x 10mm x 1mm x 2pcs (OEM Ref 90543-273-000)
Starter Brush Set
Starter Brush Set/2 1Pc Insulated Leads 1Pc Non-Insulated Leads 12mm x 14mm x 6mm For Misuba 2 Brush Starter. OEM Ref # 31201-292-158 / 31201-MG9-004
CB750K 1975-78 ~ Warning and Service Label Set
Honda CB750K (1975-78) Warning & Service Label (Sticker) Set. This set includes several warning and service labels that were originally found on these bikes when new. You'll find the quality & accuracy of these decals second to none and accurate in every detail. These reproductions will add the finishing touch to your restoration. This 8 piece warning & service label set includes: 1 - Important Information 1 - Caution: Battery 2 - Helmet Holder 1 - Exhaust Modification 1 - Engine Oil Capaciy 1 - Preserve Nature Black 1 - Preserve Nature White These decals are no longer available from the manufacturer. All decals are "printed" on the highest quality materials from companies such as 3M and Avery. All decals have a protective coating to resist scratching and to protect colors from UV rays. These decals are adhesive backed for simple application.
Engine Oil Seal Kit
7 pc. Engine Oil Seal Kit, Superior OEM Quality - Made in Japan Fits: Honda CB750K (1977-78), CB750F (1977-78) Supersport 1 pc. 91205-405-005 / 91205-405-000 Countershaft sprocket oil seal - 29.8 x 62 x 7 1 pc. 91202-216-000 / 91202-302-010 Clutch arm seal - SB type - 14 x 24 x 5 1 pc. 91206-286-005 / 91206-286-013 / 91206-286-003 Shift shaft seal - 14 x 28x 7 1 pc. 91201-300-003 Crank seal 30 x 42 x 8 1 pc. 91215-300-003 Seal - Starting clutch gear - 25 x 33 x 4 1 pc. 91204-286-003 / 91204-286-005 Kickstart Oil Seal 18 x 29 x 7 1 pc. 91211-286-003 Tach drive oil seal 4.8 x 14.5 x 4
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Chain Adjuster Stopper Set/2
Chain Adjuster Stopper Set/2. High quality steel made in Canada stoppers. These have been discontinued by Honda get these steel upgrades today! Replaces OEM# 52136-405-000 and 52136-ME1-670.
Carb Float
Carb Float with Pin, Replaces OEM # 16013-405-004 / 16013-393-004 / 16013-KCY-670 / 16013-MN1-671 Note: Order the Quantity of Floats you Require
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Alternator Cover Mounting Screw Set
Alternator Cover Mounting Screw Set. Set of 8 Mounting Screws Used to Fasten the Main Alternator Cover in place (Not the Alternator Face Plate). Replaces OEM # 93500-06032-OA X7 / 93500-06035-OA X1
NGK Iridium Spark Plug
NGK DR8EIX Iridium Spark Plug Cheapest Horsepower You Can Buy for your CB! Adds a Solid 1-2 HP to your Bike! 4 required per bike, Order the Quantity you require.
Battery Box Rubber Set
Battery Box Rubber Set. Includes Battery Rubber X1, Battery Box Collar X1, Bolt X1 and Washer X1. This set fastens into the top section of the Battery Box. Fits: Honda CB750K (1969-76) - 4 Sets Used Per Bike, CB750K (1977-78) - 3 Sets Used Per Bike, CB750F (1975-76) Supersport - 4 Sets Used Per Bike, CB750F (1977-78) Supersport - 3 Sets Used Per Bike, CB750A (1976-78) Hondamatic - 2 Sets Used Per Bike Note: Order the Quantity of Sets you Require
Gas/Fuel Tank Cap
OEM Style Gas/Fuel Tank Cap with Rubber Gasket Already Installed, Replaces OEM # 17620-399-010 Note: Does not include a chain attached to this cap.
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Front Stock Type Rim
Chrome Front Stock Type Rim, 1.85" Width x 19" x 40 Hole, Overall Actual Width 2.75". These are high quality rims made by D.I.D who originally made the OEM rims. Replaces OEM # 44701-405-771
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Stock Style Tachometer
Stock Style Tachometer, Face dial ranges from 0-12000RPM. The ratio of this Tachometer is 4:1 which is the ratio used on stock CB750's. Note: The CB Tachometers slightly changed from year to year, this may not be an exact stock match for your bike but will work great! Housing Size approx 4.6", face 3.9" Check the photo for the design.
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 1X - 4x8 Screws w Lock Washers 11X- 4x12 Screws w Lock Washers 12X- 4x16 Screws w Lock Washers
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50710-405-000
LED Upgraded Headlight Assembly
LED Upgraded Headlight Assembly - Chrome Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. H4 LED Bulb with 6000k white brightness and Bulb Dust Boot for North American Market CB750's that drive on the right side of the road. Fits: All Honda CB750's (1969-78)
Headlight Assembly
Chrome Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Halogen Lamp unit with 12v 60/55 Bulb (P43T base) and Bulb Dust Boot for North American Market CB750's that drive on the right side of the road. Fits: All Honda CB750's (1969-78)
Headlight Assembly ~ European Version
Chrome Side Mount European Version Headlight Assembly. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. 60/55 watt H4 P43T Halogen Bulb and parking light. E-Mark certified for European Market use (can also be used in North America). Fits: All Honda CB750's (1969-78)
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Front Brake Caliper Bleed Screw
Front Brake Caliper Bleed Screw. Replaces OEM # 45224-579-013
Shock Absorber Set ~ Stock Design ~ CB750K 1969-71
Stock Type Designed Shock Absorber Set - Chrome Body with Chrome Springs and Black Center. These are modelled after the original stock shocks made for the CB750K 1969-71. The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 336mm (13 1/4") Center of Eye to Eye. Stock Match for: Honda CB750K (1969-71) Will Also Fit: Honda CB750K (1972-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Shock Absorber Set ~ Stock Design ~ CB750K 1972-76
Stock Type Designed Shock Absorber Set - Chrome Body with Chrome Springs and Chrome Center. These are modelled after the original stock shocks made for the CB750K 1972-76. The original OEM shocks came with 3 position spring preload adjustments however we have upgraded these to 5 spring preload adjustments so you can better fine tune these shocks! 336mm (13 1/4") Center of Eye to Clevis. Stock Match for: Honda CB750K (1972-76) Will Also Fit: Honda CB750K (1969-71), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013