Honda ► CB750K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750K with universal parts included that match “screws nuts bolts tools”►
- Honda
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Tappet Adjuster Screw & Nut Set
Tappet Adjuster Screw & Nut Set. Each Set includes one Tappet Adjuster Screw and one Nut. Replaces OEM # 90012-426-000 (Adjuster), OEM # 90206-250-000 (Nut). Note: Order the Quantity of Sets your Bike Requires
Rear Sprocket Bolt & Nut Set
Rear Sprocket Stud Bolt (12x54) & Nut Set. Set includes 4 Stud Bolts and 4 Nuts. These Stud Bolts Fasten to the Centre Wheel Flange and Rear Sprockets. Replaces OEM # 90128-341-000 X4 (Bolts), 94030-12000 X4 (Nut)
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Handlebar Brake Lever Pivot Bolt & Nut Set
Brake Lever Pivot Bolt & Nut. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-300-000
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Swing Arm Pivot Bolt Lock Nut and Washer
Swing Arm Pivot Bolt Lock Nut and Lock Nut Washer, Replaces OEM # 90354-425-830 (Nut), 90600-425-830 (Washer)
Front Brake Caliper Rebuild Kit
Front Brake Caliper Rebuild Kit Kit includes brake caliper sealing ring, caliper bolts X2, bleed screw, bleed screw cap, and brake caliper adjuster set consisting of adjusting bolt, spring, washer and nut.
Front Brake Caliper Rebuild Kit
Front Brake Caliper Rebuild Kit Kit includes brake caliper sealing ring, caliper bolts with washers X2, bleed screw, bleed screw cap, and brake caliper adjuster set consisting of adjusting bolt, spring, washer and nut.
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Front Brake Caliper Adjuster Set
Front Brake Caliper Adjuster Set. Includes Adjusting Bolt, Spring, Washer and Nut.
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Nut
Steering Stem Nut, Replaces OEM # 90304-425-000 Sold Each, we also offer the washer for this nut
Ignition Switch Assembly
Ignition Switch Assembly Square End Plug Type - 4 Prong OEM Ref # 35100-341-700 / 35100-374-007 / 35100-369-740 Note: We offer an ignition switch nut tool to easily loosen or tighten the ignition switch nut without causing damage to the switch.
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Cylinder Head Nut Cover
Cylinder Head Nut Cover OEM Ref # 91318-300-013
Brake Rod Adjusting Nut
Brake Rod Adjusting Nut, Replaces OEM # 95015-42000
Drive Chain Adjuster Set
Complete Drive Chain Adjuster Set, Includes 2 Chain Adjusters, 2 Chain Adjusting Bolts and 2 Adjuster Nuts. Replaces OEM # 95014-19000
Ignition Coil Holder Clamp
Ignition Coil Holder Clamp with Bolt, Washer and Nut. This is the clamp that holds the ignition coil in place. Replaces OEM # 30151-300-000 / 30152-300-000
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 4X - Drain Screws with O-Rings 1X - 4x8 Screws w Lock Washers 11X- 4x12 Screws w Lock Washers 12X- 4x16 Screws w Lock Washers
DOHC Screw Set
71PC DOHC Screw Set, Includes Front Stay Plate Screws (8), CV Cap Screws (8), Throttle Cable Bracket Screw (1), Rear Stay Plate Screws (8), Vacuum Petcock Screws (6), Bowl Screws (12), Accelerator Pump Cover Screws (3), Air Cutoff Screws (8), Choke Cable Clamp Screw (1), Throttle Plate Screws (8) and Choke Plate Screws (8).
Neutral Switch Screw
Neutral Switch Screw, This is the small Screw that threads into the Neutral Switch. Replaces OEM # 35752-300-020
Points Cover Screws
Points Cover Screws (Set of 2). Fits: ALL 1969-1978 Honda CB750 Points Covers and Our Points Cover (Part #13-0000).
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Rear Wheel Bearing Retainer Ring Tool
Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch socket bar wrench tool hole. OR removing and fitting the rear wheel sprocket carrier bearing retainer ring. The perfect tool for easier removal and fitting without damaging the special retainer ring. Removes Rear Wheel Sprocket Carrier Bearing Retainer Ring on the Honda CB750K (1969-78), CB750F (1975-78) Supersport, CB750A (1976-78) Hondamatic Removes Rear Wheel Hub Bearing Retainer Ring on the Honda CB750K (1969-82), CB750A (1976-78) Hondamatic CB750C (1980-82) Custom, CB750L (1979) Limited CB650 (1979-82), CB650C (1980-81) Custom, CB650SC (1982) Nighthawk
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
High Performance Kibblewhite Cylinder Stud Nuts
High Performance Kibblewhite Black Oxide Finish Cylinder Stud Nuts Set/16. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite cylinder stud nuts are manufactured from high strength premium steel. After machining these nuts are heat treated to prevent cracking under load. The premium black oxide treatment gives an excellent, corrosion resistant appearance.
Steering Stem Head Lock Nut
Steering Stem Head Top, Thread on Lock Nut. Replaces OEM # 90302-425-830
Side Cover Emblem Attachment Nut
Side Cover Emblem Attachment Nut, Replaces OEM# 90315-504-000 Sold Each, Order the Quantity you Require
Speedo/Tach Cap Nut Set/4
Set of 4 Cap Nuts Used to Mount the Stock OEM Type Speedometer and Tachometer. Replaces OEM # 94021-06020 X4.
Brake Disc Retaining Nut Pk/10
Brake Disc Retaining Nut Pk/10, Replaces OEM # 90309-357-000
Oil Filter Bolt
Oil Filter Bolt OEM Ref # 15420-300-020
Clutch Adjuster Bolt
Clutch Adjuster Bolt, Replaces OEM# 22841-425-000
Engine Bolt Set
Engine Bolt Set, 60 Pieces, Includes 13 Different Bolt Types and 2 Allen Keys.
Throttle Adjusting Bolt
Throttle Adjusting Bolt, Replaces OEM # 53190-300-000
Carb Bolt Kit
Carburetor Bolt and Washer 46 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Carb Bolt Kit
Carburetor Bolt and Washer 43 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Clutch Cover Screw Set
Clutch Cover Screw Set. Includes all 3 Screws needed to fasten the Clutch Cover. Replaces OEM # 93700-06016-0B X3.