Honda ► CB750L ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB750L with universal parts included that match “petcock adapter plates”►
- Honda
Chrome Bullet Shaped License Plate Bolt
Chrome Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
Universal Bar Switch Assembly ~ Left (Clutch) Side
Universal Bar Switch Assembly ~ Left (Clutch) Side. Clutch side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes headlight hi-low, turn signal and horn buttons. Includes 8 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Universal Bar Switch Assembly ~ Right (Brake) Side
Universal Bar Switch Assembly ~ Right (Brake) Side. Brake side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes momentary starter, kill and on/off headlight buttons. Includes 9 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Short Stem Air Glide Mirror Set
Short Stem Chrome Billet Aluminum Oval Air Glide Mirror Set. left hand thread adapter included for Yamaha right-side perch. These mirrors will fit most Honda, Kawasaki, Suzuki & Yamaha's with a 10mm mounting hole. 10mm thread, Stem 6.1" total length, Mirror 5 1/8" wide, 2 5/8" tall, 5/8" deep.
Long Stem Air Glide Mirror Set
Long Stem Chrome Billet Aluminum Oval Air Glide Mirror Set. left hand thread adapter included for Yamaha right-side perch. These mirrors will fit most Honda, Kawasaki, Suzuki & Yamaha's with a 10mm mounting hole. 10mm thread, Stem 6.9" total length, Mirror 5 1/8" wide, 2 5/8" tall, 5/8" deep.
Micro Custom Speedometer-KPH ~ Black Face Plate
Micro (1.9") Chromed Custom Type Kilometers Per Hour (KM/H) Speedometer with Black face plate. Includes LED illumination and mounting plate, requires mounting brackets (03-0740, 03-0741, 03-0762 or 03-0763) to mount to handlebars. Face dial ranges from 0-220KM/H. The ratio of this Speedometer is 60MPH=2240 RPM. Note: These are not stock type replacement speedometers, Please ensure this is the correct ratio for your bike.
Red Reflective License Plate Bolts (Pk/2)
Red Reflective License Plate Bolts (Pk/2). Bolts include springs and wing nuts. 1" round outer diameter, 3/4" long mounting stud. Spring tension keeps them from coming loose. Do not over tighten as it will pull the back out or pop the lens off, order 2 Packs of 2 for a full set of 4.
Chrome Upswept Muffler Extension Set
Chrome upswept muffler Extension Set. These are made specifically for Triumphs but they're perfect for adapting any straight mufflers to upswept mufflers. Check the dimensions to see if they'll work on your project. Constructed of 18 gauge chromed steel and slips on stock header pipes to allow mufflers with 1 1/2" to be easily mounted. Adapters allow mounting of "classic" Triumph TR6/T120 63-70 mufflers on Hinkley Bonneville models for a classic look. Sold as a set of 2. Dimensions: Total Length = 7" Short Side = 1 1/2" OD - 1 3/8" ID Long Side = 1 5/8" OD x 1 9/16" ID Angle = 30 Degrees
Hex Head Nut
Hex Head Nut Pk/10 Plated Finish Size: 10mm
Lock Washer
Lock Washers Pk/100 Heavy Duty - Plated Size: 12mm
Beehive Black Taillight
Beehive Black Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4" Length, 3" Width, 4" Height.
Beehive Chrome Taillight
Beehive Chrome Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.