Honda ► CB900C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CB900C with universal parts included that match “screws nuts bolts tools”►
- Honda
Carburetor Cap Screw Set/8
Carburetor Cap Screw Set/8 with Metal Washers.
Turn Signal Lamp Lens Screw Set
Turn Signal Lamp Lens Screw Set/2, Replaces OEM # 93500-04025-0A ALSO Fits our Signal Lens #11-2195 and Signals #11-2114 and #11-2149
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Float Bowl Drain Screw O-Rings Pk/4
Float Bowl Drain Screw O-Rings Pk/4
Brake Caliper Bleed Screw Rubber Cap (Stock Type)
Stock Type Brake Caliper Bleed Screw Rubber Cap. These are the Same Design Rubber Caps as the Originals from the Factory. Replaces OEM # 43353-548-003
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Exhaust Stud Set
Exhaust Stud Set. Includes 8 Exhaust Studs and 8 Flange Nuts.
Drain Plug Washer
Drain Plug Washer 14mm x 20mm x 1mm
Oil Drain Plug
Magnetic Oil Drain Plug 14mm Diameter 1.5 Thread Pitch OEM Ref # 92800-14000 / 90101-14259-00
Oil Passage Cap with O-Ring
Oil Passage Cap with O-Ring. Replaces OEM # 15331-300-000 (Oil Passage Cap) and OEM # 94608-40000 (O-Ring). Note: Sold Each, Order the Quantity of Caps you Require
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-438-305 Fits M16 x 1.5 Note: These Bikes Listed Came with Either a 14.6mm Nut Thread Diameter (This Petcock) or a 16.9mm Nut Thread Diameter (Part #20-8041). Please Check Your Bikes Thread Diameter to Confirm the Petcock you Require.
Side Stand Rubber Hardware Set
Side Stand Rubber Hardware Set, Includes Metal Collar and Silver Colored Flange Bolt.
Master Cylinder Cover
Master Cylinder Cover 4 Screw Type Chrome - No Logo OEM Ref # 45513-422-671 / 45519-422-671
Starter Motor
Starter Motor Unit. Replaces OEM # 31200-438-505 This starter bolts on as direct replacements for the OEM type. Features an improved high-output permanent magnet.
Master Cylinder Reservoir Kit
Master Cylinder Reservoir Kit - Front 4 Screw Cover Note: When installing use the diaphragm plate from the old master cylinder with this kit.
Brake Switch
Front Brake Switch Fits Front 79-82 Disc Brake Models All 4 Bolt Master Cylinder Covers OEM Ref # 35340-422-003 / 35340-422-013
Honda CB Charging Rotor
Honda CB Charging Rotor, Replaces OEM # 31110-426-832 This rotor is a high quality OEM style replacement for Honda field coil rotors. The field coil is wound to stock specifications. This rotor is an easy installation and provides years of trouble free reliability from your Honda engine. Easy bolt-in installation just like the stock rotor.
Clutch Damper Repair Kit
Clutch Damper Repair Kit. Includes 7 Clutch Dampers and 7 Screws. The original dampers are often dried and hardened, preventing them from working properly often resulting in a rattling noise. This problem is especially noticeable in neutral at idle and goes away when the clutch cable is pulled in. This lack of proper dampers is hard on your bike internals, replace the old dried up dampers with a new fresh set and keep your bike running smoothly for years to come!
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Brake Nut Adjust Tool
Brake Nut Adjust Tool, 14mm Size.
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes