Honda ► CBX1000 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CBX1000 with universal parts included►
- Honda
Seal Puller
Seal Puller for Large Size Seals.
Scraper Knife
Scraper Knife 15mm Stainless Steel
Scraper Knife
Scraper Knife 20mm Stainless Steel
Blind Hole Bearing Puller Set
Blind Hole Bearing Puller Set Includes 2.15LB Slide Hammer With Shaft & 8 Pc Of Bearing Collets. Pulls The Following Size Bearings: 8-10mm, 10-12mm, 12-14mm, 15-17mm, 17-20mm, 20-24mm, 25-29mm, 30-32mm
Battery Jumper Cables
Battery Jumper Cables. 6 Feet in Length, These cables feature 10-gauge battery cables and insulated color-coded terminal clamps for safe and secure handling. The smaller clamp size easily fits motorcycle's, ATV's, UTV's, snowmobile's, watercraft's, etc.
Metric Tap & Die Set
Metric Tap & Die Set 39pc Set Includes Pitch Gauge, Die Holder, 2 Tap Wrenches, Screw Driver, Metric Taps: M3 X 0.5 M3 X 0.6 M4 X 0.75 M4 X 0.7 M5 X 0.8 M5 X 0.9 M6 X 1.0 M6 X 0.75 M7 X 0.75 M7 X 1.0 M8 X 1.0 M8 X 1.25 M10 X 1.25 M10 X 1.5 M12 X 1.25 M12 X 1.5 1/8NPT X 27 Includes 17 Dies to Match the 17 Tap Sizes Listed.
Timing Light
Timing Light Inductive Xenon Timing Light Operates From 12 Volt Battery
Alternator/Battery Checker
Alternator/Battery Checker LED Voltage, Battery & Alternator Multi-Checker. For All 12 Volt Systems
Electrical Circuit Tester
Electric Circuit Tester - Checks all motorcycle primary electrical and computer circuits for power. Plastic handle lights up if circuit is good. Icepick type probe and 48" cable with insulated alligator clips.
Spin On Oil Filter Wrench
Spin On Oil Filter Wrench Removes 63-98mm In Diameter - 3/8" Drive
Mechanics Stethoscope
Mechanics Stethoscope
Compression Tester
Compression Tester Includes Adaptors to Fit 10mm, 12mm, 14mm & 18mm Plug Holes
Hook & Pick Set
Hook & Pick Set 5 Pc Set With Magnet In Handle End
Tire Valve Stem Tool
Tire Valve Stem Tool Core Removal & Repair Tool
Brass Air Coupler Set
Brass Air Coupler Set 5 Pc Air Tool Quick Coupler Set
Tire Inflator
Tire Inflator 3 Function Inflator 2" Dial Guage 0-160PSI / 0-11KPA 12" Hose With Chuck
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Deep Allen Socket Driver Set
Deep Allen Socket Driver Set 8 Pc Set - 140mm Bits Includes 1/2" Drive, Socket Sizes - 5, 6, 7, 8, 10, 12, 14 & 17mm
Metric Pin Punch Set
Metric Pin Punch Set 8 Pc Set Includes 1.5mm, 2mm, 3mm, 4mm, 5mm, 5.5mm, 6mm & 8mm
Clutch Holding Tool
Clutch Holding Tool Adjustable Vise Grip Style Clutch Basket & Sprocket Holder Tool
Black Hand Guard Set
Black Hand Guard Set with hardware. Attaches to the handlebars to protect your hands during riding.
Wheel Weight Wrench
Wheel Weight Wrench Tool for installing and removing spoke or mag type wheel weights.
Image Scope
Professional Flexible Fiber Optic Image Scope for inspecting engine internal parts. 18" long wand with a 6mm (1/4") OD tip. Image resolution is 7,400 pixels. Packed in a blow mold case with handle jacket and extra Xenon Bulbs and 2 AA batteries.
Chain Breaker
Chain Breaker Folding Handle & Heat Treated Pin Breaks 420/520/530 Chain
T-Handle Wrench Set
T-Handle Wrench Set 7 Pc Set Includes 8, 10, 12, 14 & 17mm 6 Point Socket Wrenches & Phillips #2 & #3 Screwdriver Tips.
Oil / Fluid Container ~ 4 Liter
4 Liter Oil / Fluid Container with Long Spout.
Deluxe Shock Preload Adjusting Tool
Deluxe Shock Preload Adjusting Tool. This tool helps to adjust shock preload without damaging the shock spring collars. It fits 35mm to 75mm spring collars. Fits: Our shock sets and many other aftermarket shocks.
Deluxe Fork Seal Driver Set
Deluxe Fork Seal Driver Set. This set includes 9 high quality carbon steel fork seal drivers with split design. Use these for easy installation of most fork seals on either conventional or inverted forks. Set Contains plastic storage case and the following drivers. -35/36mm driver -39mm driver -41mm driver -43mm driver -45mm driver -46/47mm driver -48mm driver -49/50mm driver -54mm driver
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
Piston Ring Tool
Piston Ring Tool with plastic storage case. This tool is designed to prevent ring breakage during cylinder installation. This tool can be easily removed after cylinder is in position. Comes with 4 rings to accept the smallest triple to the largest single cylinder engines. Fits 40-85mm sizes.
Fork Cap Wrench ~ 35MM Size
Fork Cap Wrench ~ 35MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 35MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~32MM Size
Fork Cap Wrench ~ 32MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 32MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~30MM Size
Fork Cap Wrench ~ 30MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 30MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~24MM Size
Fork Cap Wrench ~ 24MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 24MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.
Portable Auxiliary Fuel Tank Tool
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed. Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Rotor and Sprocket Holder
Rotor and Sprocket Holder. Keeps rotors, flywheels and sprockets from rotating during removal and installation. The adjustable stop-screw keeps the tool open at a set distance. Holds sprockets and rotors with holes center to center at a minimum distance of 13mm and a maximum distance of 230mm's.
Bearing Packer
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Steering Race Remover 25-35mm
Steering Head Bearing Race Remover, Range 25-35mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 25mm to 35mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Steering Race Remover 35-55mm
Steering Head Bearing Race Remover, Range 35-55mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 35mm to 55mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Aluminum Timing Degree Wheel
Aluminum Timing Degree Wheel 7" Diameter with Large Visible Markings. This Tool Allows for Extremely Accurate Marking which Makes Getting the Timing Right the First Time a Breeze! Lightweight and Durable Tool. This Tool Can be used for Crankshaft Positioning, Ignition and Camshaft Timing.
Swing Arm / Rising Rate Linkage Bearing Install Tool
Swing Arm / Rising Rate Linkage Bearing Install Tool Designed for installation of the swingarm bearings on late-model Japanese off-road motorcycles. Puller draws bearing into the swingarm. Includes three drivers for use with common bearing sizes Kit includes driver sizes: I.D. 20mm / O.D 26mm, I.D. 21mm / O.D. 26mm & I.D. 22mm / O.D.26.8mm
Handlebar Top Clamp
Handlebar Top Clamp Chrome Custom Handlebar Top Clamp with Plated Allen Socket bolts. Mounting Holes center to center length 100mm, center to center height 35mm.
Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer
Carburetor and throttle body synchronizer kit for bikes with 2 Carbs. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2 carbs. Includes 2 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Socket Head Cap Screw Pk/10
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 15mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 20mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 25mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 30mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 35mm