Honda ► CL200 ►
-
Here’s our hand-picked list of electrical parts for your Honda CL200 with universal parts included that match “honda sl125”►
- Honda
Denso Ignition Contact Points
Contact Points (1pc.) - Replaces OEM # 30202-107-004 / 30202-216-004 / 30202-107-154 These points are for Nippondenso ignitions Only. They are NOT for Hitachi or Kokusan Ignitions. Please check which type you have before ordering. Honda used different ignition systems on some of the same years of bikes.
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-15001 Band Overall Size: 5.25" (133mm) Measuring from the inside of the brackets.
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Starter Solenoid Relay
Starter Solenoid Relay, Replaces OEM# 35850-371-670 / 35850-306/670 / 35850-HA7-670
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Ignition Coil
Ignition Coil 100MM C-C Mounting Points OEM Ref # 30400-306-672 / 30400-306-672
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.