Honda ► CL200 ►
-
Here’s our hand-picked list of electrical parts for your Honda CL200 with universal parts included►
- Honda
Starter Solenoid Relay
Starter Solenoid Relay, Replaces OEM# 35850-371-670 / 35850-306/670 / 35850-HA7-670
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-341-671
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Bar Switch Assembly ~ Left (Clutch) Side
Bar Switch Assembly ~ Left (Clutch) Side - Black. Replaces OEM # 35250-300-033
Denso Ignition Contact Points
Contact Points (1pc.) - Replaces OEM # 30202-107-004 / 30202-216-004 / 30202-107-154 These points are for Nippondenso ignitions Only. They are NOT for Hitachi or Kokusan Ignitions. Please check which type you have before ordering. Honda used different ignition systems on some of the same years of bikes.
Ignition Coil
Ignition Coil 100MM C-C Mounting Points OEM Ref # 30400-306-672 / 30400-306-672
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Ignition Switch Nut Tool
Ignition Switch Nut Tool, used to loosen and tighten the igntion switch nut properly without causing any damage to the switch.
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-15001 Band Overall Size: 5.25" (133mm) Measuring from the inside of the brackets.
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.