Honda ► CL350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL350 that match “honda sl125”►
- Honda
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 130mm Length. Replaces OEM #' 95011-14100 / 95011-14200
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Gas Tank Cap
Chrome Cap Gas Tank Cap with Gasket Installed, Replaces OEM# 17620-402-000 , 17620-402-010
Clutch Lever ~ GP Style
Clutch Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53178-369-700
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Brake Lever
Brake Lever OEM Ref # 53175-402-700 / 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700
Kickstart Rubber
Kickstart Rubber OEM Ref # 28311-329-000 / 95011-51000 / 28311-342-000
Gear Change Rubber
Gear Change Rubber OEM Ref # 95011-400-000
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. This Emblem Came in Many Different Color Combos. This is the Black Number/White Background Version. It Will Replace Any of the Other Versions. Replaces OEM# 87128-287-010 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Rear Turn Signal Stay
Rear Turn Signal Stay, Replaces OEM# 33607-286-871 / 33607-286-871B Can be used on the left or right side. Sold Each, Order the Quantity you Require.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17534-323-300
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Speedometer Cable
Speedometer Cable, Replaces OEM# 44830-KB7-000 / 44830-456-000 / 44830-437-670 / 44831-456-000 / 44830-369-700 / 44830-313-000
Performance Starter Motor
Rick's Electrics Brand Performance Hot Shot Starter Motor Unit, Replaces OEM# # 31200-286-405 / 31200-286-168 / 31200-286-158. It is an upgraded 4 brush permanent magnet starter; it includes a new cable that is longer than the stock piece for easy installation.
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850353 Please note Oil Pump Gasket Not Included
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 159mm Width: 30mm OEM Ref # 43120-KG4-006
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Cam Chain Guide Pin
Cam Chain Guide Pin OEM Ref # 14612-286-000
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
Charging Kit ~ Lithium Ion Version
Rick's Electrics Charging Kit. Kit includes both a high quality stator and lithium-ion friendly rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-286-000
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Turn Signal Replacement Lens
Turn Signal Replacement Lens (Amber) - Front or Rear OEM Ref # 33402-268-671
Turn Signal Stem
Front Signal Lamp Stay - Chrome. Body Length 65mm, Thread 25mm, Total Length 90mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Cam Shaft Roller Collar
Cam Shaft Roller Collar - Replaces OEM # 14606-286-000
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
Replacement Mirror
Replacement Mirror (R.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88110-333-611
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-287-004
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Footrest Rubbers
Footrest Rubbers Pk/2 OEM Ref # 50661-310-000 / 50661-312-000
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Replacement Mirror
Replacement Mirror (L.H) 4 1/2" Diameter, 10mm Thread. Replaces OEM# 88120-333-611
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Cam Roller Pin
Cam Roller Pin - Replaces OEM # 14605-286-020
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-300-000 / 37260-449-840 Made in Japan
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Carb Rebuild Kit
Carb Rebuild Kit for carbs with ROUND CARB BOWLS. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000