Honda ► CL350K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL350K►
- Honda
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Carb Rebuild Kit
Carb Rebuild Kit for carbs with ROUND CARB BOWLS. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder with Gasket
Carb Holder with Gasket - Replaces OEM# 16211-286-040 (Holder) and 16229-369-000 (Gasket). NOTE: This is for One Holder and One Gasket, Order the Quantity you Require. If you require band clamps, this carb holder requires our carb holder clamp #15-0684
Carb Diaphragm Rubber
Carburetor Top Diaphragm Rubber. Outer dimension 72mm - Inner dimension 25mm. Replaces the diaphragm rubber on Honda OEM# 16022-287-004 / 16022-287-014 / 16022-287-024. Note: When installing be sure to line up the rubber tab on the diaphragm so the slide is in it's proper orientation. Sold Each, order the quantity you require.
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover - Replaces OEM# 87126-455-000 These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87125-455-000 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87128-317-670 / 87129-317-670 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Left Side
Side Cover Emblem with 2 Attachment Clips ~ For the Left Side Cover - Replaces OEM# 87126-344-671 These are great quality made of a solid cast metal. Note: This is for the Left side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem ~ Right Side
Side Cover Emblem with 2 Attachment Clips ~ For the Right Side Cover - Replaces OEM# 87125-344-671 These are great quality made of a solid cast metal. Note: This is for the Right side emblem, double check the direction the Honda wing is facing to be sure this is the side you require (other side sold separately).
Side Cover Emblem
Side Cover Emblem with 2 Attachment Clips. This Emblem Came in Many Different Color Combos. This is the White Number/Burgundy Background Version. It Will Replace Any of the Other Versions. Replaces OEM# 87128-287-010 Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 36 Spokes with 36 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Fork Tube Set
Fork Tube Set/2, Length (555mm or 21.85"), 33mm OD. Replaces OEM# 51410-317-700 Before ordering Please Confirm 21.85" is the Length you would like
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Front Signal Lamp Stay
Front Signal Lamp Stay - Chrome. Body Length 40mm, Thread 30mm, Total Length 70mm. Note: We sell these in Various Lengths, Confirm this is the Size you would Like Before Purchase
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-286-000
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Rear Turn Signal Stay
Rear Turn Signal Stay, Replaces OEM# 33607-286-871 / 33607-286-871B Can be used on the left or right side. Sold Each, Order the Quantity you Require.
Speedometer Cable
Speedometer Cable, Replaces OEM# 44830-KB7-000 / 44830-456-000 / 44830-437-670 / 44831-456-000 / 44830-369-700 / 44830-313-000