Honda ► CL450 ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL450►
- Honda
Front Fuel Tank Holder Rubber
Front Fuel Tank Holder Rubber - Replaces OEM # 17611-283-010 Sold Each.
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM # 17613-292-000
Front/Rear Signal Lamp ~ 1 Wire Type
Signal Lamp - Amber - 12v - 1 wire for Front or Rear - Replaces OEM# 33600-447-000 / 33600-447-P00. Please double check you require the 1 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-292-003 / 30203-292-154
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-292-003 / 30204-292-154
Stock Type Mirror Set
Stock Type Mirror Set/2, Replaces OEM# 88110-329-730 / 88110-074-000 / 88120-329-730 / 88120-074-000 Chrome Mirrors, 8" Stem Length
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 6 1/2" Offset 4"
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Performance Charging Kit ~ Lithium Ion Version
Rick's Electrics High Performance Hot Shot Lithium Ion Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a lithium-ion battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Performance Charging Kit
Rick's Electrics High Performance Hot Shot Standard Lead Acid Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a standard lead acid battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 52108-457-300 Note: These Replace the factory plastic OEM Type Bushings.
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Side Stand Spring
Side Stand Spring, Replaces OEM # 95014-72402
Cam Chain
Cam Chain 219T x 128 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-283-003 / 94500-02128
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Cylinder Head Gasket
Cylinder Head Gasket, Replaces OEM# 12909-428-003 / 12909-283-000 / 12909-333-000.
Front Sprocket ~ 15 Tooth
Front Sprocket ~ 15 Tooth Replaces OEM# 23801-348-690 Please Count your sprocket teeth and check your chain length before ordering to ensure this is correct for your bike Note: CB450K and CL450K - some of these models used 16 or 17 tooth sprockets - confirm you require 15 tooth sprocket.
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-18000 / 40543-390-000 / 40532-283-010. If you require 2 adjusters purchase 2 of this part.