Honda ► CL450K ►
-
Here’s our hand-picked list of electrical parts for your Honda CL450K with universal parts included that match “screws nuts bolts tools”►
- Honda
![Honda CL450K Turn Signal Pinch Bolt Set](/images/parts/100/73-0840.jpg)
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
![Honda CL450K Lens Screw](/images/parts/100/49-0144.jpg)
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
![Honda CL450K Ignition Switch Assembly](/images/parts/100/12-0060.jpg)
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
![Honda CL450K Tail Light Assembly](/images/parts/100/11-2147.jpg)
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
![Honda CL450K Signal Lamp Lens w Gasket & Screws - Red](/images/parts/100/11-2160.jpg)
Signal Lamp Lens w Gasket & Screws - Red
Red Front/Rear Turn Signal Lamp Lens with Gasket and 2 Screws. OEM Ref # 33402-268-671
![Honda CL450K Performance Tool Spark Plug Crimper Tool](/images/parts/100/07-9977.jpg)
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
![Honda CL450K Terminal Crimping Tool](/images/parts/100/35-0028.jpg)
Terminal Crimping Tool
Metric Terminal Crimper Tool. Includes sizes 14-16, 14-18, 18-20, 20-24 and 22-24. Professionally Crimps like factory originals. This tool can be used with flag type terminals.
![Honda CL450K Spark Plug Gapping Tool](/images/parts/100/35-0136.jpg)
Spark Plug Gapping Tool
Circular Spark plug gap tool. Marked in thousandths of an inch and millimeters.
![Honda CL450K Heavy Duty Terminal Crimper Tool](/images/parts/100/35-0011.jpg)
Heavy Duty Terminal Crimper Tool
Heavy Duty Metric Terminal Crimper Tool, fastens metric terminals to wires. Includes sizes 10-12, 14-16 and 18-22. Professionally Crimps like factory originals.
![Honda CL450K Turn Signal Light Mount Bracket Holder Set](/images/parts/100/09-0098.jpg)
Turn Signal Light Mount Bracket Holder Set
Black Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
![Honda CL450K Turn Signal Light Mount Bracket Holder Set](/images/parts/100/09-0099.jpg)
Turn Signal Light Mount Bracket Holder Set
Chrome Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
![Honda CL450K Headlight Shell and Rim](/images/parts/100/09-0084.jpg)
Headlight Shell and Rim
Custom 7" Satin Black Side Mount Headlight Shell with Chrome Trim Ring. Designed for 7" sealed type headlights. Includes a 3 wire plug that works with sealed beam or H4 bulbs as well as the clip/screw and wire clips. Side mounting holes are threaded to use 5/16-24 bolts (bolts not included). Outer side mounting points are 7" apart. 3" Mounting depth from mounting holes to the back of the bucket. Sealed beam Headlight sold separately #09-0008 (Below), or the upgraded halogen beam #09-0051
![Honda CL450K Battery Jumper Cables](/images/parts/100/35-8020.jpg)
Battery Jumper Cables
Battery Jumper Cables. 6 Feet in Length, These cables feature 10-gauge battery cables and insulated color-coded terminal clamps for safe and secure handling. The smaller clamp size easily fits motorcycle's, ATV's, UTV's, snowmobile's, watercraft's, etc.
![Honda CL450K Alternator/Battery Checker](/images/parts/100/35-9006.jpg)
Alternator/Battery Checker
Alternator/Battery Checker LED Voltage, Battery & Alternator Multi-Checker. For All 12 Volt Systems
![Honda CL450K Electrical Circuit Tester](/images/parts/100/35-9009.jpg)
Electrical Circuit Tester
Electric Circuit Tester - Checks all motorcycle primary electrical and computer circuits for power. Plastic handle lights up if circuit is good. Icepick type probe and 48" cable with insulated alligator clips.
![Honda CL450K Front Signal Lamp Stay ~ Short Type](/images/parts/100/73-1105.jpg)
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. These are M10 x 1.50 with nut - Ensure your bike requires this thread size before purchasing. Body Length 26mm, Thread 21mm, Total Length 47mm.
![Honda CL450K LED Turn Signal Set/2](/images/parts/100/12-0131.jpg)
LED Turn Signal Set/2
Custom LED Turn Signal Set/2. 3.5" Long Turn Signals with 10" Long Wires, DC 12 Volt. Will screw on to 10mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
![Honda CL450K Custom LED Turn Signal Set/2](/images/parts/100/12-0132.jpg)
Custom LED Turn Signal Set/2
Custom LED Amber Lens Turn Signal Set/2. 2.5" Long Turn Signals with 10.5" Long Wires, DC 12 Volt. Will screw on to 8mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
![Honda CL450K Horn with Chrome Grill](/images/parts/100/32-7521.jpg)
Horn with Chrome Grill
Horn with Chrome Snap on/off Grill Cover. 12 Volt, 2.5 Amp, 95mm Diameter. Two wire hookup, with spade terminals. Tone adjustment screw on backside.
![Honda CL450K Custom Chrome Dual Beam Headlights](/images/parts/100/09-0087.jpg)
Custom Chrome Dual Beam Headlights
Custom Chrome 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
![Honda CL450K Custom Matte Black Dual Beam Headlights](/images/parts/100/09-0088.jpg)
Custom Matte Black Dual Beam Headlights
Custom Matte Black 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
![Honda CL450K Universal Ignition Switch Bracket](/images/parts/100/12-0039.jpg)
Universal Ignition Switch Bracket
Chrome Universal Ignition Switch Bracket. Switch hole is 22.5mm, bolt hole is 9.5mm, overall length is 75mm. Fits to our #12-0058 Sold Separate
![Honda CL450K Hydraulic Brake Light Switch](/images/parts/100/29-7002.jpg)
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
![Honda CL450K Chrome Mini Retro Hooded Tail Light](/images/parts/100/09-0093.jpg)
Chrome Mini Retro Hooded Tail Light
Chrome Mini Retro Hooded Tail Light with Mounting Hardware. Features a pivoting mounting base bracket. Includes running light, brake light and tag light functions. Uses a standard 21/5 watt 1157 bulb. Wire lead is about 10" long. Housing is 2 1/8" round x 3 3/8" long over all. Stands about 3 1/4" tall from base of mounting bracket. Mounting base is 2" long x 3/4" wide. Mounting bolt holes are 1/4" holes x 1 1/4" center to center.
![Honda CL450K Satin Black Mini Retro Hooded Tail Light](/images/parts/100/09-0094.jpg)
Satin Black Mini Retro Hooded Tail Light
Satin Black Mini Retro Hooded Tail Light with Mounting Hardware. Features a pivoting mounting base bracket. Includes running light, brake light and tag light functions. Uses a standard 21/5 watt 1157 bulb. Wire lead is about 10" long. Housing is 2 1/8" round x 3 3/8" long over all. Stands about 3 1/4" tall from base of mounting bracket. Mounting base is 2" long x 3/4" wide. Mounting bolt holes are 1/4" holes x 1 1/4" center to center.
![Honda CL450K Vintage Round Chrome Taillight](/images/parts/100/09-0100.jpg)
Vintage Round Chrome Taillight
Vintage All Steel Round Chrome Taillight with plate bracket, bolts and washers. 1 5/8" Round plastic lens (with a clear bottom to light up your plates), 12 volt double filament bulb. Works as a running and brake light. Base mounting plate measures 2" top to bottom and 2 1/2" wide. Mounting base 6mm holes are 1 1/4" wide x 7/8" top to bottom, tag mounting plate measures 6 1/2" wide, tag mounting holes 4 1/2" centered.