Honda ► CL450K ►
-
Here’s our hand-picked list of parts and accessories for your Honda CL450K with universal parts included►
- Honda
Gas/Fuel Tank Cap Latch Assembly
Gas/Fuel Tank Cap Latch Assembly, Includes Chrome Latch, Return Spring, Latch Mounting Pin and C-Clip.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Carb Float
Carb Float with Pin, Replaces OEM # 16013-283-004 Note: Sold Each, Order Quantity of Floats your Bike Requires.
Starter Solenoid Relay
Starter Solenoid Relay OEM Ref # 35850-375-000 / 35850-286-027
Hot Shot Rectifier/Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Hot Shot Lithium Ion Battery Compatible Rectifier-Regulator. Designed with a lower voltage set point to work with lithium ion batteries only. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. Dimensions 54mm Length, 57mm Width, 35mm Height. High quality Part. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Performance Charging Kit ~ Lithium Ion Version
Rick's Electrics High Performance Hot Shot Lithium Ion Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a lithium-ion battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please contact the manufacturer of your Lithium Ion Battery to ensure our product has the correct set point for their product.
Performance Charging Kit
Rick's Electrics High Performance Hot Shot Standard Lead Acid Battery Compatible Charging Kit. This high performance Hot Shot charging kit includes both a new rotor and a standard lead acid battery compatible combination rectifier / regulator which looks like the stock unit and mounts in the same location. The kit will put out approximately 150 watts: 50% over stock. You do NOT need to replace your OE stator unless it tests bad, this kit works with the OE stator. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Condenser
Condenser - Replaces OEM# 30250-369-004 / 30280-292-672 / 30280-292-671 / 30280-371-000
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Stock Type Fork Gaitors
Black Stock Type Fork Gaitors (Set/2) OEM Ref. # 51611-300-000
Fork Seals
Fork Seal Set - 35 x 46 x 11. Made In Japan by OEM supplier. Replaces OEM # 91255-292-003
Fork Gaiters
Fork Gaiters OEM Ref # 51611-300-000 Note: These are about 1.75" shorter then the stock type but will work fine
Fork Spacer Trim Set
Chrome Front Fork Spacer Trim Set/2. These are the Chrome Ribs that Cover the Top of the Fork Boots. Replaces OEM # 51608-300-000
High Performance Kibblewhite Bronze Swingarm Bushing Set
High Performance Kibblewhite Bronze Swingarm Bushing Set/2. Replaces OEM# 52108-457-300, 52108-422-300. Made in the USA by Kibblewhite who have been making High Quality Performance parts for 75+ years. Kibblewhite bronze bushings offers increased durability and better fitment then the OEM type bushings.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Sprocket Side - Replaces OEM# 41231-283-000 This retainer is used on the (sprocket side) of the bike.
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 23 bolts and 2 Allen keys for a total of 25 pieces. These bolts are all smooth head Allen bolts and are for the visible covers only.
Fuel Petcock
Fuel Petcock - Replaces OEM # 16950-292-000 - Fits M16 x 1.5 Note: Please Check that the Size Listed Above is Correct for your Bike before ordering
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Swingarm Pivot Bolt Locknut with Washer
Swingarm Pivot Bolt Locknut with Locknut Washer. Replaces OEM # 90354-268-000 (Locknut) and OEM # 90526-268-000 (Washer).
Swingarm Dust Seal Cap (Set/2)
Swingarm Dust Seal Metal Cap (Set/2). These Metal Caps go on the Ends of the Swingarm Pivot. Replaces OEM # 52144-283-010 X2
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Clutch Plate
Clutch Plate 1 Piece Required OEM Ref # 22201-283-000 / 22201-MA7-000
Carb Rebuild Kit
Carb Rebuild Kit for carburetor models 14H and 14L which were used on 5 speed 450's. There are several different carb models for the CB450 and CL450 so please make sure to check your carb model number before ordering. The main jet sizes in the later model carbs are larger. (#145 or #150) Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Rebuild Kit
Carb Rebuild Kit for the 5 speed 450's. Note: Each Kit Rebuilds One Carb, Order the Quantity of Kits you Require
Carb Holder
Carb Holder with Gasket - Replaces OEM# 16211-283-000 NOTE: This is for One Holder, These Bikes Use 2 Of These So Purchase 2 If Replacing Both Holders. If you require band clamps, this carb holder requires our carb holder clamp #15-0685
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Side Cover Emblem
Cast Metal Side Cover Emblem with the 3 Attachment Clips for the rear of the emblem (You must use your old bolt and washers that attach at the front of the emblem). Replaces OEM # 87130-294-010 / 87130-319-671 / 87125-346-670 Note: There are a few different styles of side cover emblems used on these bikes. Be sure to verify this design is the type you need before purchasing. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Lens Screw
Tail Light Lens Screws, Pack of 10. Replaces OEM # 93500-04050-4J ISO Std. Pitch - Steel Plated Size: 4 x 50mm
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Shock Absorber Washer
Shock Absorber Washer, Used when Installing Shocks. Replaces OEM # 90521-292-000 Note: Washers sold Each, order the quantity you require
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Cam Chain 219FTSS x 128
Cam Chain 219FTSS x 128 D.I.D (Daido) Takes 01-8802 Rivet Link Pitch: .3061" Side Plate: Steeped Parallel Plate Average Tensile Strength: 1896lbs OEM Ref # 14401-283-003 / 94500-02128
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Rear Wheel Spoke Set
Rear Spoke Set with Nipples - 40 Spokes with 40 Nipples. Note: Spokes are Silver in Color and Nipples are Gold in Color. For Stock 18" Rear Type Rims Only
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-110-000
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 95011-31000
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Fork Cover Rubber Set
Fork Cover Rubber Set/2, Replaces OEM # 51601-300-000
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Turn Signal Pinch Bolt Set
Turn Signal Pinch Bolt Set. Includes 2X Chrome Bolts, 2X Hex Nuts and 4X Flat Washers. This set is used to clamp the turn signal onto the stem. Some models originally had a 25mm long bolt but these will interchange. This set includes hardware for 2 turn signals. If you need enough for all 4 signals please purchase 2 sets.
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Bronze Thrust Bushing Set/2
Bronze Thrust Bushing Set/2. Replace the cheaply made, worn-out factory swingarm bushings with a 2-piece set of brand-new bronze thrust bushings. Replaces OEM # 52109-283-300