Honda ► CM200T ►
-
Here’s our hand-picked list of parts and accessories for your Honda CM200T with universal parts included that match “1”►
- Honda
6 1/2" Headlamp Unit
6 1/2" Outer Diameter Headlamp Unit. This unit can be used with various headlights requiring a 6 1/2" headlamp. Can replace OEM# 33120-333-670 / 33100-333-671 but this unit does not have any mounting clips on the rear sides of the headlamp unit. Does Not Include mounting hardware. This unit comes with a H4 60/55w bulb, all glass lens with pilot light.
Carburetor Air Mixture Screw Kit
Carburetor Air Mixture Screw Kit Set Includes 1 Mixture Screw, 1 Spring, 2 O-Rings. Order The Quantity of Sets you Require.
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-216-000 / 18291-MN5-650 Sold Each, Order the Quantity you Require
Carb Float
Carb Float with Pin, Replaces OEM # 16013-405-004 / 16013-393-004 / 16013-KCY-670 / 16013-MN1-671 Note: Order the Quantity of Floats you Require
Gas/Fuel Tank Cap
OEM Style Gas/Fuel Tank Cap with Rubber Gasket Already Installed, Replaces OEM # 17620-399-010 Note: Does not include a chain attached to this cap.
Fuel Petcock
Fuel Petcock Assembly, Replaces OEM# 16950-GF6-015 / 16950-163-035 / 16950-GW8-670 / 16950-149-025 / 16950-195-702 / 16950-150-000 / 16950-164-015 / 16950-164-025 / 16950-164-035 / 16950-KE6-830 Fits M14 x 1.0
Rectifier / Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier / Regulator. Replaces OEM# 31600-KV8-681 / 31600-413-008. Designed with a lower voltage set point to work with lithium ion batteries only. Rick's design does not include the black signal wire. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Rectifier Regulator
Rectifier Regulator 6 Wires - 3 Yellow in One Connector Block + 3 Wires in 4 Space Block OEM Ref # 31600-KV8-681 / 31600-413-008 / 31600-MC9-740
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50710-405-000
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17631-329-003
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Stock Type Battery Band
Stock Type Battery Band, Replaces OEM# 95012-17001 Band Overall Size: 6.125" (155mm) Measuring from the inside of the brackets.
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Cotter Valve / Valve Keeper
Cotter Valve / Valve Keeper, Replaces OEM# 14781-107-003 / 14781-107-020. 2 Used For Each Valve Spring. Sold Each, Order the Quantity you Require
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-382-004 / 16011-393-004 / 16011-KG0-891 / 16030-1007 / 16030-028 / 16011-382-004
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.
Chrome Bungee Nut Set/2 ~ 6mm x 1.00mm
New chrome pair of grooved Bungee Nuts 6mm x 1.00mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 8mm x 1.25mm
New chrome pair of grooved Bungee Nuts 8mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 10mm x 1.25mm
New chrome pair of grooved Bungee Nuts 10mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Carb Rebuild Shop Kit - 5mm x 1,200 Bolt/Washer Assortment
1202 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Valve Lapping Stick
Valve Lapping Stick 1 1/8" & 1 3/8" Cups
Muffler Clamp
Muffler Clamp - Universal Fits 1 1/2"
Foot Pegs
Chromed Foot Pegs Pk/2 Rubber Inlay 1" & 1 1/4" Clamp Universal Fit
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes