Honda ► CM400A ►
-
Here’s our hand-picked list of electrical parts for your Honda CM400A with universal parts included►
- Honda
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
6 1/2" Headlamp Unit
6 1/2" Outer Diameter Headlamp Unit. This unit can be used with various headlights requiring a 6 1/2" headlamp. Can replace OEM# 33120-333-670 / 33100-333-671 but this unit does not have any mounting clips on the rear sides of the headlamp unit. Does Not Include mounting hardware. This unit comes with a H4 60/55w bulb, all glass lens with pilot light.
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Tail Light Lens
Tail Light Lens OEM Ref # 33702-329-671 / 33702-092-671
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Ignition Switch Assembly
Ignition Switch Assembly Rectangular Connector Block With 6 Flat Male Terminals OEM Ref # 35100-MC0-671/ 35100-413-007 / 35100-465-770
Rectifier / Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier / Regulator. Replaces OEM# 31600-KV8-681 / 31600-413-008. Designed with a lower voltage set point to work with lithium ion batteries only. Rick's design does not include the black signal wire. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Rectifier Regulator
Rectifier Regulator 6 Wires - 3 Yellow in One Connector Block + 3 Wires in 4 Space Block OEM Ref # 31600-KV8-681 / 31600-413-008 / 31600-MC9-740
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"
Headlight Bracket Set (34mm)
Aluminum Custom Headlight Brackets 34mm Headlight Mounting Holes 7/16"
Headlight Bracket Set
Headlight Bracket Set - Black 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Custom Universal Headlamp
Custom Universal Headlamp 4 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Custom Universal Headlamp
Custom Universal Headlamp 5 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Rectangular Headlamp
Small Rectangular Headlamp 6.5"x4.5" Lens Steel Lens Frame, With Black Plastic Housing Halogen Bulb & Headlamp Plug With Wires Side Mount, 14mm Mounting Holes, 7.25" Width Two Openings On Back
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
Headlight Assembly
Chrome 7" Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. H4 Bulb with European style parking light (Not used for North American models)
Classic Round Black Taillight
Classic Round Black Taillight with plate bracket. 2 1/4" Round lens (with a clear bottom to light up your plates), 12 Volt double filament bulb. Works as a running and brake light.
Mini Bates Style LED Taillight ~ Chrome
Mini Bates Style LED Taillight ~ Chrome. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Mini Bates Style LED Taillight ~ Black
Mini Bates Style LED Taillight ~ Black. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Beehive Chrome Taillight
Beehive Chrome Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.
Beehive Black Taillight
Beehive Black Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4" Length, 3" Width, 4" Height.
Vintage Round Black Taillight
Vintage All Steel Round Satin Black Taillight with plate bracket. 1 5/8" Round lens (with a clear bottom to light up your plates), 12 volt double filament bulb. Works as a running and brake light. Base mounting plate measures 2" top to bottom and 2 1/2" wide. Mounting base 6mm holes are 1 1/4" wide x 7/8" top to bottom, tag mounting plate measures 6 1/2" wide, tag mounting holes 4 1/2" centered.
Black Sparto Tailight
Tail Light Assembly - Black Sparto Classic 50's design. Dual filament Bulb. Not DOT approved for Highway use.
Headlight Shell and Rim
Custom 7" Satin Black Side Mount Headlight Shell with Chrome Trim Ring. Designed for 7" sealed type headlights. Includes a 3 wire plug that works with sealed beam or H4 bulbs as well as the clip/screw and wire clips. Side mounting holes are threaded to use 5/16-24 bolts (bolts not included). Outer side mounting points are 7" apart. 3" Mounting depth from mounting holes to the back of the bucket. Sealed beam Headlight sold separately #09-0008 (Below), or the upgraded halogen beam #09-0051
LED Taillight
Custom LED Taillight. Small and lightweight, this cool little LED taillight includes a swiveling mounting bracket with about 100 degrees of up or down adjustment making it ideal for many custom applications. Featuring a clear lens with 8 super bright red LED's for the taillight and brake light as well as 5 clear LED's for the license plate illumination. Machined from aluminum in anodized black. Not DOT approved. Dimensions are approximately 1-7/8" wide x 1-3/4" deep.
Black Tail Lamp Assy. - Custom British Style
Black Tail Lamp Assy. - Custom British Style with alloy mount bracket and license plate illumination. These are perfect for many cafe and custom projects. Includes everything shown. Lens Dimensions: 4-1/2" Wide, 2-1/8" High, 1-3/4" Depth Full Assembly Dimensions: 7" Total Width, 5-1/2" Total Length, 3-1/2" Total Height
Custom Chrome Dual Beam Headlights
Custom Chrome 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.