Honda ► CM400E ►
-
Here’s our hand-picked list of electrical parts for your Honda CM400E with universal parts included that match “honda sl125”►
- Honda
Tail Light Lens
Tail Light Lens OEM Ref # 33702-329-671 / 33702-092-671
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Front Reflector
Front Reflector, Replaces OEM# 33742-HB9-641 / 33741-413-003 / 33741-413-013 Amber Reflector with Black Plastic Ring. 2 Segments in the Reflector (Instead of 6 Like the OEM).
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Rectifier / Regulator ~ Lithium Ion Battery Compatible
Rick's Electric Brand Lithium Ion Battery Compatible Rectifier / Regulator. Replaces OEM# 31600-KV8-681 / 31600-413-008. Designed with a lower voltage set point to work with lithium ion batteries only. Rick's design does not include the black signal wire. This is Not for use with standard lead acid batteries. The voltage set point is 14V +/- .2. Please ensure this set point is correct for your battery before attempting installation.
Rectifier Regulator
Rectifier Regulator 6 Wires - 3 Yellow in One Connector Block + 3 Wires in 4 Space Block OEM Ref # 31600-KV8-681 / 31600-413-008 / 31600-MC9-740
6 1/2" Headlamp Unit
6 1/2" Outer Diameter Headlamp Unit. This unit can be used with various headlights requiring a 6 1/2" headlamp. Can replace OEM# 33120-333-670 / 33100-333-671 but this unit does not have any mounting clips on the rear sides of the headlamp unit. Does Not Include mounting hardware. This unit comes with a H4 60/55w bulb, all glass lens with pilot light.
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Turn Signal Lamp ~ 2 Wire Type
Signal Lamp - Amber - 12v - 2 wire for Front or Rear - Replaces OEM# 33400-341-702 / 33400-413-671. Please double check you require the 2 wire type before purchasing Stem *Our Part Number 11-2167*
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Ignition Switch Assembly
Ignition Switch Assembly Rectangular Connector Block With 6 Flat Male Terminals OEM Ref # 35100-MC0-671/ 35100-413-007 / 35100-465-770
Turn Signal Lamp Gasket
Turn Signal Lamp Gasket, Replaces OEM # 33443-268-671
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Starter Clutch Diode
Starter Clutch Diode OEM Ref # 31700-124-003 / 31700-166-008
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.