Honda ► CR250R ►
-
Here’s our hand-picked list of parts and accessories for your Honda CR250R with universal parts included►
- Honda
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
JIS Screw Bit Set
JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3. Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face. It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
Chain Clip Link Remover Pliers
Chain Clip Link Remover Pliers. Slim jaw design allows for easy install and removal of chain clip links.
T Handle Hex Key Set (SAE Type)
T Handle Hex Key Set (SAE Type), with Metal Holder. Contains Sizes- 3/32", 7/64", 1/8", 9/64", 5/32", 3/16", 7/32", 1/4", 5/16", 3/8".
T Handle Hex Key Set (Metric Type)
T Handle Hex Key Set (Metric Type), with Metal Holder. Contains Sizes- 2.0mm, 2.5mm, 3.0mm, 4.0mm, 4.5mm, 5.0mm, 5.5mm, 6.0mm, 8.0mm, 10.0mm
Brush Cleaning Tool
Blue Chain Cleaning Brush/ Gear Cleaner Tool.
Brake Nut Adjust Tool
Brake Nut Adjust Tool, 14mm Size.
Valve Lapping Stick
Valve Lapping Stick 1 1/8" & 1 3/8" Cups
Valve Lapping Stick
Valve Lapping Stick 5/8" & 13/16" Cups
Valve Lapping Stick Set
Valve Lapping Stick Set/2 5/8" & 13/16" Cups 1 1/8" & 1 3/8" Cups
Flywheel Puller
Flywheel Puller 35mm x 1.5 Right Hand Thread External Thread Flywheels & Rotors
Tire Lever - 16.5" Spoon Type w Handle
Tire Lever - 16.5" Spoon Type, Forged Steel with Plastic Handle.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
Aluminum Vise Insert
Aluminum Vise Insert. A perfect addition to make your workbench vise more versatile. Three machined semi circles to hold 5/16" to 9/16" size parts you need to grip. The bridge spring keeps the jaws aligned and allows the inset to open precisely with the vise.
Chain Alignment Tool
Chain Alignment Tool. This tool provides an easy way to verify your chain is aligned properly to the front and rear sprockets after rear wheel or chain maintenance. Simply clamp this tool on the rear sprocket with the rod pointing to the front sprocket. With the rod as your guide, make visual alignment then adjust the chain adjusters as needed to correct alignment.
Brake Bleeder Hose Kit
Brake Bleeder Hose Kit. Kit includes 1-way valve, hose and clamps. This tool helps bleed motorcycle brakes quickly and easily. The 1-way valve prevents air from flowing back into the brake lines. Easy to use, simply connect and pump.
Steering Bearing Installation Tool
Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly any lower bearing. Use with a soft faced hammer.
Combination Flywheel Puller Driver Set
10 Piece Combination Flywheel Puller Driver Set. Used to separate flywheel from the crankshaft taper. Supplied in a labelled plastic storage case. This 10 pieces set provides 15 different applications, sizes as follows： M14x1.5, M16x1.5, M18x1.5, M19x1.0, M20x1.0, M27x1.25, M22x1.0, M25x1.5, M22x1.5, M26x1.5, M24x1.0, M27x1.0, M26x1.0, M28x1.0, M28x1.5 Except for M27X1.0, all applications have right hand threads.
Folding Trail T-Handle Kit
Folding Trail T-Handle Kit Come with 4 Sockets - 8mm, 10mm, 12mm & 13mm.
Spark Plug Wrench
Spark Plug Wrench Fits 18mm Spark Plugs 160mm Overall Length
Fusil Type Tire Lever
Fusil Type Tire Lever Chrome Finish
Dunlop Type Tire Lever
Dunlop Type Tire Lever 16" Long
Chain Press Assembly Tool
Chain Press Assembly Tool Used to Press On Sideplates on rivet or clip rear drive chains
Chain Breaker
Chain Breaker 520/530/630 Chain
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders
Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2, 3 or 4 cylinders. Includes 4 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Safety Wire
Stainless Steel Safety Wire 25 Foot Roll of .032" Dia Wire
Oil / Fluid Container ~ 2 Liter
2 Liter Oil / Fluid Container with Long Spout.
Piston Pin Puller
Piston Pin Puller Fits Piston Sizes from 40mm (1 5/8") to 100mm (4") and Piston Pins From 12mm to 17mm Tool has 2 threaded steps 12mm and 17mm. Diameter of the rod that goes through the piston pin is 8.5mm..
Wheel Bearing Remover Set
8 Piece Metric Wheel Bearing Remover Set in a Plastic Case. Includes a large and small driver with 10mm, 12mm, 15mm, 17mm, 20mm and 25mm removers. Dependable split collet design.
Tire Pressure Gauge
Tire Pressure Gauge Dial Type Measures From 10-60 PSI
6-Way Spoke Wrench
6-Way Spoke Wrench Fits #7 Thru #12 nipples
Impact Driver Set
Impact Driver Set Heavy Duty Impact Driver With Slip Resistant Rubber Grip Comes with 6 Piece Bit Set & Case 1/2" Drive, Can also be used with 1/2" Drive Socket
Round Magnetic Parts Dish
Round Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 149mm Diameter, 40mm Height.
Rectangular Magnetic Parts Dish
Rectangular Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 9.5" Length, 5.5" Width, 1.1" Height.
3/8" Drive Click Type Torque Wrench Tool
3/8" Drive Window Click Type Torque Wrench Tool with Black Plastic Storage Case. 10-100Ft. Lbs. This click-style torque wrench easily tightens various automotive bolts, from lugs and crankshaft bolts to cylinder heads and engine-mountings. Measures from 10 to 100 foot/pounds in .5 increments.
Extractor & Drill Set
10 Piece Extractor & Drill Set in a Plastic Case. Set contains 5X extractors (#1 through #5) and 5X mechanic's length cobalt drills. Removes bolts and screws up to 5/8". Cobalt Drill and Screw Extractor Sizes: 5/64", 7/64", 5/32", 1/4", 19/64"
Cylinder Stud Installation Tool Set
3 Piece Cylinder Stud Installation Tool Set. Installs studs without damaging the threads. Steel construction with black oxide finish for longer tool life. Includes M6 x 1.00, M8 x 1.25 and M10 x 1.25 stud installers. Hex head is 19mm.
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Stud Extractor 6-12mm
Stud Extractor 3/8" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (6-12mm)
Impact Driver
Impact Driver Heavy Duty #2500 Driver complete with 4 Piece 2" Hex bits. This driver is 3/8" drive can also be used with any 3/8" drive socket.
Replacement Bit Set
Replacement Bit Set 1 1/2" Standard Driver Bit Set Fits 35-0106 & 35-0095 Impact Drivers Contains 2 Phillips & 2 Slotted Bits
Cable Luber
Cable Luber Used on All Cables, Best way to lube & clear cables of moisture & Dirt.
Spoke Wrench Set
Spoke Wrench Set Fits #8/9 & #10/11 Chrome
Replacement Bit Set
Replacement Bit Set 3" Long Driver Bit Set Fits 35-0106 & 35-0095 Impact Drivers Contains 2 Phillips & 2 Slotted Bits