Honda ► CRF250X ►
-
Here’s our hand-picked list of electrical parts for your Honda CRF250X with universal parts included►
- Honda
![Honda CRF250X Universal 1 Ohm Dual Output 6V Ignition Coil](/images/parts/100/17-6924.jpg)
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
![Honda CRF250X Cylinder Wire Set](/images/parts/100/23-2901.jpg)
Cylinder Wire Set
Cylinder Wire Set Black Gum Rubber - Copper Core 2 Pcs 15" Long 2 Pcs 12" Long
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3106.jpg)
Spark Plug Cap
Spark Plug Cap KLG Rubber Waterproof Type Non-Resistor Universal For 14mm Plugs
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3114.jpg)
Spark Plug Cap
Spark Plug Cap Short Bakelite Type For 12mm & 14mm Plugs Universal Non Resistor 90 Degree Elbow Type NGK - LZFH Style
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3115.jpg)
Spark Plug Cap
Spark Plug Cap - SB05F 10 & 12mm Thread
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3118.jpg)
Spark Plug Cap
Spark Plug Cap - LD05F 10mm & 12mm Thread
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3119.jpg)
Spark Plug Cap
Spark Plug Cap - XD05F 10mm & 12mm Thread
![Honda CRF250X Spark Plug Cap](/images/parts/100/23-3123.jpg)
Spark Plug Cap
Spark Plug Cap - XB05F 14mm Thread
![Honda CRF250X LED Charging System Guage](/images/parts/100/24-2660.jpg)
LED Charging System Guage
LED Charging system indicator Gauge. Shows Voltage of your alternator rising and falling with RPM and gives a clear indication of your charging systems normal operation and early warning of problems. Gauge is Bright High Quality Chrome plated and clamps onto 7/8" Bars and can be easily wired into any point in the system (before a switched load is best). Can be mounted as shown or to handlebar by clamp (included).
![Honda CRF250X Hydraulic Brake Light Switch](/images/parts/100/29-7002.jpg)
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
![Honda CRF250X Relay with Base ~ 4 Pin ~ 12v 40Amp](/images/parts/100/32-7513.jpg)
Relay with Base ~ 4 Pin ~ 12v 40Amp
Relay with Base ~ 4 Pin ~ 12v 40Amp. This relay is typically used for on/off applications such as horn/aux lights etc.
![Honda CRF250X Relay with Base ~ 5 Pin ~ 12v 40Amp.](/images/parts/100/32-7514.jpg)
Relay with Base ~ 5 Pin ~ 12v 40Amp.
Relay with Base ~ 5 Pin ~ 12v 40Amp. This relay is typically used for hi/low beam applications.
![Honda CRF250X Classic Chrome Horn](/images/parts/100/32-7516.jpg)
Classic Chrome Horn
Classic Chrome Horn, 12 Volt, 3.9" Diameter, 105 Decibel. Mounting Bracket Holes 30mm apart center to center.