Honda ► CX500C ►
-
Here’s our hand-picked list of parts and accessories for your Honda CX500C with universal parts included that match “1”►
- Honda
Oil Filter
Oil Filter OEM Ref # 15412-413-005 / 154A1-413-005 / 154A1-MA6-000
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Clutch Cable
Clutch Cable, Replaces OEM# 22870-MA1-000 , 22870-ME2-000
Cam Chain
Silent Cam Chain 417 x 78 OEM Ref # 14401-MA1-013 / 14401-MA1-003 / 14401-ME2-003 Made In Japan
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Turn Signal Lamp
Turn Signal Lamp 1-Wire - Rear OEM Ref # 33400-377-671 / 33400-460-671 / 33400-460-679
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Front Brake Caliper Piston
Front Brake Caliper Piston (1) - 42.8mm Diameter x 41mm Length - OEM Ref # 45107-415-006
Water Temperature Sending Unit O-Ring
Water Temperature Sending Unit O-Ring - 13.5 x 1.4 - Replaces OEM# 91307-PH7-660 / 91307-611-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Fuel Petcock
Fuel Petcock, Replaces OEM# 16951-385-703 / 16951-385-701 / 16951-385-702
Starter Motor Seal
Starter Motor Seal - Size 24.4 x 3.1, Replaces OEM# 91312-MG7-003 / 91309-300-000 / 91309-425-003
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Engine Oil Seal Kit
Engine Oil Seal Kit - 10 Pc Kit Includes: Camshaft Seal, Clutch Rod Seal, Water Pump Seal, Tachometer Gear Seal, Shift Shaft Seal, Final Driver Gear Seal 1, Final Driver Gear Seal 2, Final Driver Gear Seal 3, Final Driver Gear Seal 4 and Final Shaft Seal.
Carburetor Screw Kit
Carburetor Screw Kit. Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 5x12 Screws w Lock Washers 8X - 4x16 Screws w Lock Washers 8X - 6x14 Screws w Lock Washers 5X - 5x16 Screws w Lock Washers 6X - 4x12 Screws w Lock Washers 4X - 4x10 Screws w Lock Washers
Fork Dust Boot Set
Fork Seal Dust Boots (Set/2). 33mm Size, Replaces OEM # 91254-413-881
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Sidecover Damper Rubber A
Rubber Sidecover Damper A, Replaces OEM # 17247-303-000
Speedo Gear Plug
Speedo Gear Plug - Plug 15mm Outer Diameter, 22mm Long. This Plug is Great for Keeping your Original Speedo Drive Gear Clean.
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50716-371-660
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Brake Rod Spring
Brake Rod Spring. Replaces OEM # 95014-73100
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.