Honda ► GL1000 ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1000►
- Honda
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Brake Pedal Pin
Brake Pedal Pin, Replaces OEM# 46503-371-000
Special Clutch Washer
Special Angled Clutch Washer (16mm), Replaces OEM# 90481-292-000
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Clutch Plate
Clutch Plate 7 Pieces Required .138" Thickness OEM Ref # 22201-300-000 / 22201-371-000
Clutch Plate
Clutch Plate 1 Piece Required .138" Thickness OEM Ref # 22202-371-000 / 22202-390-000 / 22202-392-000
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required OEM Ref # 22321-283-000 / 22321-MG8-000
Clutch Plate Set (8 Plates)
Clutch Plate Set of 8 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 7X Clutch Friction Disk "A" (Replaces OEM# 22201-371-000 / 22201-300-000) and 1X Clutch Friction Disk "B" (Replaces OEM# 22202-392-000 / 22202-371-000).
Clutch Spring Kit
Clutch Spring Kit. Note: There will be extra springs in this kit for some bikes.
Water Temperature Sending Unit O-Ring
Water Temperature Sending Unit O-Ring - 13.5 x 1.4 - Replaces OEM# 91307-PH7-660 / 91307-611-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-371-305
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #65, Main Jet #125, Pilot Jet #35, Needle Jet, Jet Needle #D143Z, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Aluminum Plug, Packing, Spring, 2X Cotter Pins, 2X Metal Washers, Nut, Rubber Plug and 6 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #62, Main Jet #120, Pilot Jet #35, Needle Jet, Jet Needle #D143Z, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Aluminum Plug, Packing, 2X Springs, 2X Cotter Pins, 2X Metal Washers, Nut, Rubber Plug and 6 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #62, Main Jet #120, Pilot Jet #35, Needle Jet, Jet Needle #D304, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Aluminum Plug, Packing, 2X Springs, 2X Cotter Pins, 2X Metal Washers, Nut, Rubber Plug and 4 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #60, Main Jet #120, Secondary Jets #60, 120, 130 and 140, Needle Jet, Low Speed Jet #38, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Packing, 2X Springs, 2X Metal Washers, Nut, Rubber Plug and 5 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Standard Carb Rebuild Kit
Standard Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat, Secondary Jets #60, 130 and 140, Needle Jet, Low Speed Jet #35, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Packing, Spring and 5 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Rubber Passage Plug
Rubber Passage Plug Pk/5 OEM Ref # 16010-371-004
Intake Manifold O-Ring (Pk/2)
Carburetor Intake Manifold O-Rings (Pack of 2), Replaces OEM # 91301-371-005 Size 40 x 2.6 Order the Quantity you Require.
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Cylinder Head Intake Boot O-Rings (Set/4)
Cylinder Head Intake Boot O-Rings, Size 40 x 2.6 (Set of 4). Replaces OEM # 91301-371-005 / 91325-413-830 These are Used Where the Manifolds Attach to the Cylinder Heads.
Seat Cover GL1000 1975-77
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Complete installation instructions as well as step by step instructions on how to repair damaged seat foam can be found in the instructions section of our website.. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Seat Cover GL1000 1978-79
Replacement Seat Cover with Reinforced Passenger Strap (No trim or hardware included just re-use existing hardware). There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Complete installation instructions as well as step by step instructions on how to repair damaged seat foam can be found in the instructions section of our website. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Side Cover Emblem
Cast Metal Side Cover Emblem with Attachment Clips. Replaces OEM # 87130-431-670 This is a Stock Type Replacement Emblem for the Honda GL1000K 1977-79 - Some 1977's used decals instead of emblems. Note: 2 Emblems Used Per Bike, Order the Quantity you Require
Cylinder Head Emblem
Cylinder Head Emblem with Attachment Clips, Replaces OEM# 12312-371-610 / 12312-371-611
Final Gear Cover Gasket
Final Gear Cover Gasket - Replaces OEM# 11372-463-003 / 11372-463-306 / 11372-371-010 / 11372-371-306 / 11372-371-000
Clutch Oil Pump Gasket
Clutch Oil Pump Gasket - Replaces OEM# 15229-371-000
Oil Passage Gasket
Oil Passage Gasket - Replaces OEM# 15128-371-000
Water Joint Thermostat Gasket
Water Joint Thermostat Gasket - Replaces OEM# 19429-371-306 Note: 2 used per bike, order the quantity you require
Cylinder Head Cover Gasket
Cylinder Head Cover Gasket - Replaces OEM# 12391-371-306 / 12391-371-000
Points Cover Gasket
Points Cover Gasket - Replaces OEM# 30376-371-000 Note: 2 used per bike, order the quantity you require
Breaker Points Gasket
Breaker Points Gasket, Replaces OEM# 30079-371-306
Water Pump Gasket
Water Pump Gasket - Replaces OEM# 11396-371-306
Cylinder Head Gasket
Cylinder Head Gasket - Replaces OEM# 12251-371-003 / 12251-371-306
Front Left Timing Belt Cover Gasket
Front Left Timing Belt Cover Gasket - Replaces OEM# 11832-371-010 / 11832-371-000
Front Right Timing Belt Cover Gasket
Front Right Timing Belt Cover Gasket - Replaces OEM# 11831-371-010 / 11831-371-000
Clutch Cover Gasket
Clutch Cover Gasket - Replaces OEM# 11393-371-000 / 11393-371-306
Transmission Cover Gasket
Transmission Cover Gasket - Replaces OEM# 11391-371-306 / 11391-371-000
Lens Screw
Tail Light Lens Screws, Pack of 10 Screws. Replaces OEM # 93500-04055-4J ISO Std. Pitch - Steel Plated Size: 4 x 55mm
Speedometer & Tachometer Crimp Ring Set/2
Speedometer & Tachometer Crimp Ring Set/2 for NIPPON SEIKI gauges. When changing the speedometer or tachometer face plates these rings are often damaged. Get a new set today to have your speedo & tachometer restoration looking perfect! Dimensions: Inner diameter 103.4mm. - Outer diameter 108.2mm.
Speedometer / Tachometer Glass Lens Rubber Seal
Speedometer or Tachometer Glass lens Rubber Seal. This seal is used when replacing the glass on the Speedo or Tach. Fits: All 92mm (3.6") glass lenses. Sold each, order the quantity you require
Speedometer & Tachometer Replacement Glass Lens Set/2
Speedometer & Tachometer 92mm Glass Lens Set/2. If the glass lens of your gauges have scratches or are broken, with these glass lenses you are able to repair your gauges' lenses. These glass lenses are slightly bent like the original glass lenses.