Honda ► GL1000LTD ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1000LTD with universal parts included that match “1”►
- Honda
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal
Oil Pump Rebuild Kit
Oil Pump Rebuild Kit Each Kit Contains: Each Kit Contains 91207-580-015 (Oil Seal 10x25x7) x1, 91208-MN1-771 (O-Ring 11x15x3) x1, 91302-200-000 (O-Ring 33.5x3) x1, 94201-30450 (Split Pin 3.0 x45) x1, 15128-371-000 (Oil Passage Gasket) x1, 15229-371-000 (Clutch Oil Pump Gasket) x1.
Drain Plug Washer
Drain Plug Washer 14mm x 20mm x 1mm
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 30 x 45 x 9.5
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Water Temperature Sending Unit O-Ring
Water Temperature Sending Unit O-Ring - 13.5 x 1.4 - Replaces OEM# 91307-PH7-660 / 91307-611-000
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Honda GL1000 Goldwing 1977 Replica Handlebar
Honda GL1000 Goldwing 1977 and GL1000L 1976 Replica Handlebar. Replaces OEM # 53100-371-980 / 53100-371-660 Thickness - 7/8" - 22mm, Length - 32 3/8" - 822mm, Pull Back - 8" - 203mm, Inner Rise - 8 3/4" - 222mm, End Rise - 9 3/4" - 248mm, Center Width - 6 1/2" - 165mm, Base Width - 10 1/2" - 266mm, Knurl Width - 4 1/2" - 114mm, Control Length - 10 1/4" - 260mm, Drilled YES There are Holes For Internal Wiring and Switch Positioning
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 51 Bolts and 1 Allen key for a total of 52 pieces. These bolts are all smooth head Allen bolts and are for the visible covers only.
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch - OEM Ref # 35350-300-006 / 35350-300-016 / 341-83980-30-00 10mm x M1.25 thread
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Rear Turn Signal Rubbers Pk/2
Rear Turn Signal Rubbers Pk/2, Replaces OEM # 33606-371-000 These are the Rubbers that Go Under the Rear Turn Signal Stays.
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Carb Body Seal, Carb Cap O-Ring, Carb Bowl O-Ring, Needle & Seat 1.0, Main Jet #62, Main Jet #120, Pilot Jet #35, Needle Jet, Jet Needle #D143Z, Air Mixture Screw, Air Mixture Spring, Emulsion Tube, Aluminum Plug, Packing, 2X Springs, 2X Cotter Pins, 2X Metal Washers, Nut, Rubber Plug and 6 Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Clutch Plate Set (8 Plates)
Clutch Plate Set of 8 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 7X Clutch Friction Disk "A" (Replaces OEM# 22201-371-000 / 22201-300-000) and 1X Clutch Friction Disk "B" (Replaces OEM# 22202-392-000 / 22202-371-000).
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Fuel Petcock Gasket
Fuel Petcock Gasket. Replaces OEM # 16955-268-020
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Valve Guide Clip
Valve Guide Clip, Replaces OEM # 12211-250-310 Sold Each, Order the Quantity you Require
Honda OEM Type Grips
Honda OEM Type Rubber Grip Set - Black - Closed end type for 7/8" bars. These are replica's of the original type grips from the factory. 135mm Length. Replaces OEM #' 53165-342-670 / 53166-342-670
Brake Lever ~ GP Style
Brake Lever - Custom GP Style in Silver, This Has More of a Bend/Kickback then the stock lever. Replaces OEM # 53175-369-003
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. This Boot Attaches to where the Brake Hose Joins to the Master Cylinder. Replaces OEM # 45522-300-010
Tail Light Lens
Tail Light Lens OEM Ref # 33702-341-671
Fork Seals
Fork Seals Set/2 36 X 48 X 11
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Front Wheel Bearing Retainer
Front Wheel Bearing Retainer - Replaces OEM# 44643-300-000
Throttle Sleeve
Nylon Throttle Sleeve - Replaces OEM # 53141-300-010
Stop Light Switch
Rear Stop Light Switch OEM Ref # 35350-292-003 / 35350-KJ9-405
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50716-371-660
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Oil Filter
Oil Filter OEM Ref # 15410-426-010 / 15410-422-004 / 16099-003 / 36Y-13441-00 Note: If you require new oil filter o-rings, springs or washers we sell these on our site as well
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.