Honda ► GL1100 ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1100 that match “honda sl125”►
- Honda
Honda GL1100 Goldwing 1980-83 Replica Handlebar
Honda GL1100 Goldwing 1980-83 Replica Handlebar. Replaces OEM # 53100-MB9-800 / 53100-MB9-670 / 53100-463-670 Thickness - 7/8" - 22mm Length - 32 1/8" - 820mm Pull Back - 10" - 254mm Inner Rise - 8 3/4" - 222mm End Rise - 10" - 254mm Center Width - 6 1/2" - 165mm Base Width - 9 1/2" - 241mm Knurl Width - 4 1/2" - 114mm Control Length - 10 1/2" - 266mm Drilled NO There are Holes For Switch Positioning
Front Cable/ Stop Switch Clip
Front Cable Clip, This Clip Holds the Stop Switch Wires to the Cable to Keep Things Tidy. Replaces OEM # 45465-270-000
Replacement Mirror
Replacement Mirror - Fits Right Or Left Honda LTD 8" Stem, 10mm Thread, Chrome Plated
Ignition Spark Unit
Aftermarket Ignition Spark Unit for Honda - 2 units required per bike. Replaces Honda OKI or NEC units. Replaces OEM Ref # 30400-MA4-601
CB Black Mirror - Original Type - DOHC
Mirror - Honda Black Type - 8" Stem, 10mm. RH threads. Original Stock Type For: Honda CB750K (1979-82), CB750F (1979-82) Supersport, CB750L (1979) Limited, CB900F (1981-82) Supersport, GL1100 (1981-83) Will also fit Any Honda: CB Note: These Fit Both Left And Right Side Of Bike, Order 2 For A Complete Set
Speedometer / Tachometer Internal Rubber Seal
Speedometer / Tachometer Internal Rubber Seal. This internal rubber seal replaces the ripped, dried or missing rubber internal seal. This internal rubber seal fits to any stock type Honda CB750 ND brand gauges.
Master Cylinder Reservoir Cap
Master Cylinder Cap with Plastic O-Ring. Replaces OEM # 45513-341-771 This style of master cylinder cap was discontinued long ago by Honda. We have had these produced again to keep your bike looking sharp. Spruce up your Master Cylinder with one of these great looking master cylinder caps!
Black Seat Cover Set GL1100 1983
Replacement Black Seat Cover Set (No trim or hardware included just re-use existing hardware). There is a layer of foam sewn into the top if the seat cover to improve ride comfort and smooth out any defects in the seat foam. There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available. Complete installation instructions as well as step by step instructions on how to repair damaged seat foam can be found in the instructions section of our website. This is for the SEAT COVER, Not the Full Seat.
Passenger Floorboard Set
Complete Passenger Floorboard Set Includes All Mounting Hardware
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-MB9-004
Rear Fender Bolt Set
Rear Fender Bolt Set of 2, Replaces OEM# 90102-371-000 These are the large main bolts that go in the middle portion of the rear fender. The grab bar bolts thread into these fender bolts.
Turn Signal Replacement Lens ~ Smoked
Turn Signal Replacement Lens - Smoked - Front Or Rear OEM Ref # 33402-431-782
Tail Light Lens Screws
Tail Light Lens Screws, Set of 4. Replaces OEM # 90147-147-671
Sintered Brake Pads
Rear Brake Pads Pk/2 Sintered Pads OEM Ref # 43105-MA3-007
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Horn Sub Harness
Horn Sub Harness, This is the Harness that Attaches to the Horn. Replaces OEM # 32103-463-000
Taillight Sub Harness
Taillight Sub Harness "A", Replaces OEM # 32101-463-000
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Primary Chain
Primary Chain - 60 Link OEM Ref # 23131-371-004 Made In Japan
Radiator Fan Cooling Switch O-Ring
Radiator Fan Cooling Switch O-Ring, Replaces OEM# 91307-PH9-000
Thermostat Cover O-Ring
Thermostat Cover O-Ring - 54 x 2 Size - Replaces OEM# 91307-MB0-003 / 91307-MB0-000 / 91302-317-700
Front Sintered Metal Brake Pad Set
Brake Pad Set - Sintered Metal - 90 x 49 x 9mm - OEM# 45105-KN8-026