Honda ► GL1100I ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1100I with universal parts included►
- Honda
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Press In Type Pilot Jet Set ~ Size #35 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #35) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #35 which is the stock size for these bikes, please confirm this is the size you require before purchasing. If you require oversize pilot jets we carry those as well.
Press In Type Pilot Jet Set ~ Size #38 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #38) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #38 which is oversize for these bikes, please confirm this is the size you require before purchasing.
Press In Type Pilot Jet Set ~ Size #42 (Pk/4)
Press In Type Pilot Jet Set of 4 (Size #42) Pilot Jets (your idle and low speed operation) are critical for smooth idling and lower rpm driving. When rebuilding carbs it is highly recommended to replace these pilot jets to ensure your bike is running as well as possible. Also, when installing new exhaust or high flow air filters it is recommended to increase the size of your Pilot Jets. These are size #42 which is the oversize for these bikes, please confirm this is the size you require before purchasing.
Oil Tube Plug
Oil Tube Plug, Replaces OEM # 15337-300-010
Handlebar Brake Lever Pivot Bolt Set
Handlebar Brake Lever Pivot Bolt, Washer & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Washer and Nut. Replaces OEM # 90114-422-000 (Bolt).
Carb Bolt Kit
Carburetor Bolt and Washer 35 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Turn Signal Relay
Turn Signal (Flasher) Relay. OEM Style Replacement 12V/23W, 3 Prong, Comes with Rubber Mount Attached. Replaces OEM # 38301-415-671 Not for Use with Custom LED Lights
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-551-020 Sold Each, Order the Quantity you Require.
Intake Manifold Assembly "A"
Intake Manifold Assembly "A" - Replaces OEM# 17110-431-010 Full assembly Includes the Metal intake manifold, brand new pliable rubber carb holder, adjustment screw and O-Ring. These integral Intake manifolds have been discontinued for decades, we have had them re-manufactured to keep these Goldwings on the road! 2X "A" Manifolds used per bike, Order the quantity you require
Intake Manifold Assembly "B"
Intake Manifold Assembly "B" - Replaces OEM# 17120-431-010 Full assembly Includes the Metal intake manifold, brand new pliable rubber carb holder, adjustment screw and O-Ring. These integral Intake manifolds have been discontinued for decades, we have had them re-manufactured to keep these Goldwings on the road! 2X "B" Manifolds used per bike, Order the quantity you require
Side Cover Emblem
Side Cover Emblem, Replaces OEM# 83605-MG9-000 / 83605-MG9-010 / 83605-463-000 / 83605-463-505 Sold Each, Order the Quantity you Require
Clutch Cover Hardware Set
Clutch Cover Hardware Set. Set includes the 6 Bolts and 2 Nuts Used to Fasten the Clutch Cover. Includes 4X 95801-0608500 , 2X 95801-0603500 , 2X 94050-06000
Chrome Timing Belt Cover Set
Chrome Timing Belt Cover Set, Replaces OEM# 11511-371-010 / 11521-371-010. Spruce up your bike with a new set of chrome covers. These new covers really make these bikes look amazing!
Air Chamber Gasket
Air Chamber / Plenum Gasket, Replaces OEM# 16075-463-004 Fix those unseen air leaks with this gasket.
Handlebar Clamp Hardware Set
Handlebar Clamp Hardware Set. This Hardware Set is for the Stock Type Clamp (Holder) that Attaches Over the Handlebar. Includes the 4 Bolts that Fasten the Handlebar Clamp in Place and 4 Covers that Snap into the Screw Tops to Give it a Super Clean Look! Replaces OEM# 91456-371-770 X4, 90185-371-000 X4
Front Brake Caliper Bolt Set
Front Brake Caliper Bolt Set, Replaces OEM# 90123-371-000. Each set includes 2 bolts and 2 washers - enough for either the left or right caliper. If you would like bolts for both sides purchase 2 sets.
Fuel Tank Rubber "C"
Fuel Tank Rubber "C" - Replaces OEM# 17616-371-000 This rubber is used with the stock bolt and collar to attach through the hole near the top of the fuel tank.
Oil Pump Rebuild Kit
Oil Pump Rebuild Kit Each Kit Contains: Each Kit Contains 91207-580-015 (Oil Seal 10x25x7) x1, 91208-MN1-771 (O-Ring 11x15x3) x1, 91302-200-000 (O-Ring 33.5x3) x1, 94201-30450 (Split Pin 3.0 x45) x1, 15128-371-000 (Oil Passage Gasket) x1, 15229-371-000 (Clutch Oil Pump Gasket) x1.
Fuel Petcock Assembly
Fuel Petcock (Gas Tap) Assembly with Port O-Rings, Replaces OEM# 16950-371-025 / 16950-MG9-005 This petcock has a "reserve" function that did not appear on the original GL1200 petcock. Outside diameter of port is 6 mm and inside diameter is 4mm
Honda Lock Key Setting Spring
Lock key setting spring - Genuine Honda - Quality made in Japan OEM # 37222-463-000
Honda Brand OEM ~ Cotter Valve
Honda Brand OEM ~ Cotter Valve. This is a genuine Honda made Cotter Valve, Replaces OEM# 14781-551-000 Sold Each, Order the Quantity you Require
Honda Brand OEM ~ Neutral Switch with Screw
Honda Brand OEM ~ Neutral Switch with Screw, OEM# 35752-300-020 Honda does not include the O-Ring, we sell those separately
GL1000/1100/1200 Water Pump ~ Genuine Honda
GL1000/1100/1200 Water Pump - Genuine Honda OEM ~ Quality made in Japan OEM # 19200-MG9-680/681 19200-371-000/010/020
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length
Grips
Sportbike Gel Grip Set Closed End Type 5" Inside Length x 7/8" 135mm Length