Honda ► GL1200I ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1200I with universal parts included that match “1”►
- Honda
Fuel Cut Relay
Fuel Cut Relay, Replaces OEM # 36100-MB1-701
Oil Pump Rebuild Kit
Oil Pump Rebuild Kit Each Kit Contains: Each Kit Contains 91207-580-015 (Oil Seal 10x25x7) x1, 91208-MN1-771 (O-Ring 11x15x3) x1, 91302-200-000 (O-Ring 33.5x3) x1, 94201-30450 (Split Pin 3.0 x45) x1, 15128-371-000 (Oil Passage Gasket) x1, 15229-371-000 (Clutch Oil Pump Gasket) x1.
Drain Plug Washer
Drain Plug Washer 14mm x 20mm x 1mm
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 30 x 52 x 7
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Water Temperature Sending Unit O-Ring
Water Temperature Sending Unit O-Ring - 13.5 x 1.4 - Replaces OEM# 91307-PH7-660 / 91307-611-000
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Deluxe Carb Rebuild Kit
Deluxe Carb Rebuild Kit - Includes Chamber Gasket, Needle & Seat #1.6, Needle Jet #D513, Air Screw, Air Spring, Main Jet #102, Slow Jet #35, 2 Metal O-RIngs, Metal End Plug, 8X Rubber O-Rings. 1 Kit Needed Per Carb, Order The Quantity you Require
Master Cylinder Cover w Diaphragm & Screws
Master Cylinder Cover with Diaphragm and Screws, Replaces OEM # 45513-MB4-673 (Reservoir Cap), OEM # 45520-MA5-672 (Diaphragm) and OEM # 93600-04012-1G (Screws).
Ignition Coil
Ignition Coil 1.9ohm Primary, 13.4K ohm Secondary Can be Used With Contact Point Ignitions OEM Ref # 30500-422-003 / 30500-422-013 / 30510-MA6-013
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 41 Bolts and 1 Allen key for a total of 42 pieces. These bolts are all smooth head Allen bolts and are for the visible covers only.
Clutch Plate
Clutch Plate "B" - Replaces OEM # 22202-ML8-000 , 22202-ML8-600 1 Piece Used per Bike, Order the Quantity You Require
Rubber
Rubber, Replaces OEM # 19051-KA4-000 High Quality Made in Japan.
Radiator Cap
Radiator Cap, Replaces OEM# 19045-MZ3-405 This cap measures 2" in diameter. Some early models of the GL1200 have a different radiator then later models. This cap is designed for a 1.5 inch hole. Check the size of your hole to be sure this will fit before purchasing.
Steering Stem Washer
Chrome Steering Stem Washer, Replaces OEM # 90503-283-000 Sold Each, order the quantity you require.
Clutch Lever Switch
Clutch Lever Switch, Replaces OEM# 35330-MB0-003
Clutch Plate Set (9 Plates)
Clutch Plate Set of 9 Plates. This includes the Fiber Clutch Plates Only (No Steel Plates). Includes 8X Clutch Friction Disk "A" (Replaces OEM# 22201-ML8-600 , 22201-ML8-000) and 1X Clutch Friction Disc "B" (Replaces OEM# 22202-ML8-600 , 22202-ML8-000)
Rear Master Cylinder Reservoir Diaphragm
Rear Master Cylinder Reservoir Diaphragm. Replaces OEM # 45520-300-000
Steering Stem Head Lock Nut
Steering Stem Head Top, Thread on Lock Nut. Replaces OEM # 90302-425-830
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Oil Filter Washer - Each
Oil Filter Washer - Each 30mm OD - 20.5mm ID - .5mm Thickness Replaces OEM# 15414-300-000 Sold Each, Order the Quantity you Require
Valve Guide Clip
Valve Guide Clip, Replaces OEM # 12211-250-310 Sold Each, Order the Quantity you Require
Chrome Spin On Oil Filter
Chrome Spin On Oil Filter Replaces Stock OEM Housing, Filter Bolt and Paper Element Filter. Note: When installing screw in the threaded bung first and then install the filter onto the bung.
Helmet Holder Lock w Keys
Helmet Holder Lock with Keys, Replaces OEM # 50710-086-007
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Center Stand Spring
Center Stand Spring. Replaces OEM # 95014-71702
Oil Filter
Oil Filter OEM Ref # 15410-426-010 / 15410-422-004 / 16099-003 / 36Y-13441-00 Note: If you require new oil filter o-rings, springs or washers we sell these on our site as well
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.
Chrome Bungee Nut Set/2 ~ 6mm x 1.00mm
New chrome pair of grooved Bungee Nuts 6mm x 1.00mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 8mm x 1.25mm
New chrome pair of grooved Bungee Nuts 8mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 10mm x 1.25mm
New chrome pair of grooved Bungee Nuts 10mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Carb Rebuild Shop Kit - 5mm x 1,200 Bolt/Washer Assortment
1202 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Valve Lapping Stick
Valve Lapping Stick 1 1/8" & 1 3/8" Cups
Muffler Clamp
Muffler Clamp - Universal Fits 1 1/2"
Foot Pegs
Chromed Foot Pegs Pk/2 Rubber Inlay 1" & 1 1/4" Clamp Universal Fit
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes