Honda ► GL1500I ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL1500I with universal parts included►
- Honda
Standard Carb Rebuild Kit
Standard Carburetor Rebuild Kit Includes: 2 Chamber Gaskets, Needle & Seat #2.6, Needle Jet D268, Air Mixture Screw, Air Spring, Main Jet #148, Slow Jet #65, Main Jet Housing, Screw, 5 Metal Washers, Spring and 4 Various O-Rings. Sold Each, Order the Quantity you Require.
Cylinder Head Intake Boot O-Rings (Set/4)
Cylinder Head Intake Boot O-Rings, (Set of 4). Replaces OEM # 16010-MT2-004 / 16010-MAM-000 / 16010-MAM-A60 These are the O-Rings Between the Intake Plate and Carb Body.
Black Seat & Back Rest Cover
High Quality Replacement Black Seat & Back Rest Cover. Features a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, made of special cold resistant outdoor 4 way stretch marine vinyl material. These fasten just like the original covers. PLEASE NOTE BELOW This cover fits the earlier style of seat, the lower passenger Lombard support are thinner on this models and also the passenger backrest sides do not go out as far. this cover does not have any storage compartments built in. please compare your seat to the one that is shown here to ensure the right on is ordered. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference
Red/Black Seat & Back Rest Cover GL1500
High Quality Replacement Red/Black Seat & Back Rest Cover. Features a layer of foam sewn into the top of the seat cover to improve ride comfort and smooth out any defects in your seat foam. There is not a "Honda" stencil on the rear of the cover due to copyright. Each seat cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, made of special cold resistant outdoor 4 way stretch marine vinyl material. These fasten just like the original covers. Complete installation instructions as well as step by step instructions on how to repair damaged seat foam can be found in the instructions section of our website. PLEASE NOTE BELOW This cover fits the earlier style of seat, the lower passenger Lombard support are thinner on this models and also the passenger backrest sides do not go out as far. this cover does not have any storage compartments built in. please compare your seat to the one that is shown here to ensure the right on is ordered. This is for the SEAT COVER, Not the Full Seat, Photo Shows Seat Cover Installed for reference.
Glove Box/Fairing Pocket Cover
Replacement Glove Box/Fairing Pocket Cover. Each cover is made entirely by hand in North America, it is crafted slowly with great care by a gifted master upholster, using only the top grade materials available.
Rear Rocker Cover Gasket
Rear Rocker Cover Gasket - Replaces OEM# 12318-MN5-000 Note: 2 used per bike, order the quantity you require.
Air Feed Pipe Gasket
Air Feed Pipe Gasket - Replaces OEM# 17142-MN5-000 Note: 2 used per bike, order the quantity you require.
Timing Belt Cover Gasket
Timing Belt Cover Gasket - Replaces OEM# 11561-MN5-650 / 11561-MN5-000 / 11561-MN5-306 Note: 2 used per bike, order the quantity you require.
Cylinder Head Gasket
Cylinder Head Gasket - Replaces OEM# 12251-MN5-004 / 12251-MN5-003 / 12251-MN5-013 . 12251-MZ0-760 Note: 2 used per bike, order the quantity you require.
Intake Manifold Gasket
Intake Manifold Gasket (Card Stock Material Style) - Replaces OEM# 17231-MN5-003 Note: 2 used per bike, order the quantity you require.
Transmission Cover Gasket
Transmission Cover Gasket - Replaces OEM# 11391-MN5-000 / 11391-MN5-650 / 11391-MZ0-760
Cylinder Head Cover Gasket
Cylinder Head Cover Gasket - Replaces OEM# 12314-MAF-000 / 12314-MN5-000 Note: 2 used per bike, order the quantity you require.
Rear Engine Case Gasket
Rear Engine Case Gasket - Replaces OEM# 21112-MN5-000 / 21112-MN5-306 / 21112-MN5-650
Clutch Cover Gasket
Clutch Cover Gasket - Replaces OEM# 11351-MN5-000 / 11351-MN5-010 / 11351-MN5-306 / 11351-MN5-651
Speedometer Cable
Speedometer Cable
Master Cylinder Rubber Boot
Master Cylinder Rubber Boot. Replaces OEM # 45522-422-000
Stock Type Gearshift Lever Rubber
Stock Type Gearshift Lever Rubber, Replaces OEM # 24781-419-000
Water Temperature Sending Unit
Water Temperature Sending Unit, Replaces OEM # 37750-PC1-004
Fork Cap O-Ring (Set of 2)
Fork Cap O-Ring Set of 2. Size 33.2 x 2.4mm. Replaces OEM # 91356-KF0-003
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17682-679-013
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Radiator Cap
Radiator Cap, Replaces OEM# 19045-MZ3-405 This cap measures 2" in diameter. Some early models of the GL1200 have a different radiator then later models. This cap is designed for a 1.5 inch hole. Check the size of your hole to be sure this will fit before purchasing.
Carb Float with Pin
Carb Float with Pin, Replaces OEM# 16013-MAM-000 / 16013-MT2-004 / 16013-MN5-004 Sold Each, Order the Quantity you Require
Side Cover Rubber Set
Side Cover Rubber Set of 4. Replaces OEM# 83551-MA6-000 X2, 83551-300-000 X1, 83601-MN5-000 X1 Each Set/4 Includes Enough Rubbers for One Side Cover
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Honda Lock Key Setting Spring
Lock key setting spring - Genuine Honda - Quality made in Japan OEM # 37222-463-000
Side Cover Emblem ~ Genuine Honda Brand
Genuine Honda Brand OEM ~ Side Cover Emblem - OEM# 83605-MT8-010 / 83605-MN5-000 This can be used on either side cover. Post to post about 80mm. Sold Each, Order the Quantity you Require
Filler Lid Lock with Keys ~ Genuine Honda Brand OEM
Filler Lid Lock with 2 Keys ~ Genuine Honda Brand ~ OEM# 37220-439-007
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"