Honda ► GL500 ►
-
Here’s our hand-picked list of parts and accessories for your Honda GL500 with universal parts included►
- Honda
Handlebar Rubber Boot
Handlebar Rubber Boot. Replaces OEM # 53180-425-010
Speedo/Tachometer Meter Cushion
Speedo/Tachometer Meter Cushion, Replaces OEM # 37235-323-700
Fuse Box Assembly
Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM # 38200-425-005
Rear Brake Rod Assembly
Rear Brake Rod Assembly, Includes Brake Rod, Spring, Brake Arm Joint, Brake Rod Adjusting Nut, Brake Rod Joint Pin and Cotter Pin.
Passenger Rear Footrest Rubber Set
Passenger Rear Footrest Rubber Set/2, Replaces OEM # 50716-371-660
Front Wheel Bearing Retainer Ring Tool
Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar wrench tool hole. The perfect tool for easier removal and fitting without damaging the special retainer ring.
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Brake Rod Joint
Brake Rod/Arm Joint, Replaces OEM # 95015-32001
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Water Temperature Sending Unit
Water Temperature Sending Unit, Replaces OEM # 37750-611-154
Tach Drive Plug Block Off w O-Ring
Tach Drive Plug (Block Off) with O-ring. This plug is generally used when the tachometer cable drive is removed and still needs to be blocked off to prevent oil leakage. This plug has an o-ring groove machined in it for better sealing. Several bike builders just cut the stock cable off and left the Honda cable drive end installed in the valve cover. This plug is a much cleaner option in both functionality and looks. These plugs are a real nice touch when you are not using the stock tachometer, and need to eliminate the cable, or are using an electronic tach. Installs in about a minute, no need to remove the valve cover to remove the tach drive gear assy. Fits tachometer cables that are approximately 15mm in diameter with a 10.5mm groove and held in place with a screw.
Fuse Box Plate Cover Screw Set
Black Fuse Box Plate Cover Screw (Set of 2). Replaces OEM # 93700-05020-0G
Tail Light Lens Screws
Tail Light Lens Screws, Set of 4. Replaces OEM # 90147-147-671
Footrest Rubbers
Footrest Rubbers (Set/2) - OEM Ref # 50661-425-670
Brake Cam Dust Seal
Brake Cam Dust Seal, Replaces OEM # 43134-300-000
Brake Caliper Bleed Screw
Brake Caliper Bleed Screw. Replaces OEM # 43352-568-003 Please Note: This item has various Applications, it is used on either the front brake caliper, Rear brake caliper or clutch slave cylinder. Confirm it is used for the application you require before ordering. Sold Each, Order the Quantity you Require
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90113-422-000 (Bolt) and OEM # 94002-06000-0S (Nut).
Handlebar Brake Lever Pivot Bolt & Nut Set
Handlebar Brake Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Brake Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-MA5-671 (Bolt) and OEM # 94050-06000 (Nut)
Carb Bolt Kit
Carburetor Bolt and Washer 24 Piece Kit. This is a Complete Bolt Kit for All 4 Carburetors.
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Custom Performance Magnetic Oil Drain Plug ~ Joker Machine
Joker Machine Brand ~ Custom Performance Magnetic Oil Drain Plug - 12mm. Dia x M1.5 - OEM Ref # 92800-12000 Plug features an extended length HIGH POWER "rare earth" Neodymium-Iron-Boron Magnet pressed into the body which grabs steel debris from your tank and motor exceptionally well! High Quality CNC machined part made in the U.S.A. Works on the oil tank drain (right side of bike) and on the oil pan drain (beneath the engine) - use two for the ultimate engine oil debris collection set-up.
Valve Spring Retainer
Valve Spring Retainer, Replaces OEM # 14771-551-020 Sold Each, Order the Quantity you Require.
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Seat Setting Rubber ~ Honda Brand OEM
Seat Setting Rubber ~ Genuine Honda Brand OEM # 77204-312-000 Sold Each, Order the Quantity you Require
Honda Brand OEM ~ Cotter Valve
Honda Brand OEM ~ Cotter Valve. This is a genuine Honda made Cotter Valve, Replaces OEM# 14781-551-000 Sold Each, Order the Quantity you Require
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Peanut Plate Fits 219T Cam Chains
Clip Link
Cam Chain Clip Link Peanut Shape Fits 25H Cam Chains
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BS05MH TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Peanut Shape Fits BF05M TSUBAKI
Cam Chain Rivet Link
Cam Chain Rivet Link Fits 82RH2015
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Push/Pull Style Throttle Assembly
Custom Dual Cable Style (Push/Pull) Throttle Assembly for 7/8" bars. Satin Black Die-Cast aluminum housing with a nylon throttle tube. Housing is threaded to accept Honda push/pull throttle cables. Opens carbs up to 38mm. Allen key included for assembly. Pull cable thread size is M10 x 1.25mm, Push cable thread size is M12 x 1.00mm. Throttle is 6" total in length.
Heated Grips
Heated Grip Set/2 for 7/8" HANDLEBARS ONLY. Warms up when the engine is running. Features a high/low/off switch. Easy to use relay protected sealed controls. Rubber resistant to low temperatures and resists cracking. Easy install with no gluing needed. 130mm Length
Classic Coke Bottle Grips
Classic Coke Bottle Grip Set - Black - 130mm Length - Closed End - for 7/8" bars.
Grips
Rubber Cushion Grip Set Gran Tourismo - Dual Wall - Black With Closed Ends For 1" Bars, 130mm Length
Grips
Roadhawk Grip Set Chrome Plate Ends With Roadhawk Design 5" Inside Length x 7/8"
Grips
Cushion Grip Set Straight Design With Chrome Ends 5 3/4" Inside Length x 7/8" 150mm Length