Honda ► GL500I ►
-
Here’s our hand-picked list of electrical parts for your Honda GL500I with universal parts included that match “honda sl125”►
- Honda
Ignition Spark Unit
Aftermarket Ignition Spark Unit for Honda - 2 units required per bike. Replaces Honda OKI or NEC units. Replaces OEM Ref # 30400-MA4-601
Tail Light Lens Screws
Tail Light Lens Screws, Set of 4. Replaces OEM # 90147-147-671
Rick's Electrics ~ Alternator Stator
Rick's Electrics Brand OEM Style Alternator Stator - Installation Instructions Included.
Fuse Box Plate Cover Screw Set
Black Fuse Box Plate Cover Screw (Set of 2). Replaces OEM # 93700-05020-0G
Starter Solenoid Relay
Starter Solenoid Relay with Fuse. Replaces OEM # 35850-MB0-007
Starter Relay Pigtail / Plug
Starter Relay Pigtail / Plug Connects to our starter relays #24-2004, 24-2157 and 73-0824. Despite wire colors you must confirm wire orientation before hooking up!
Turn Signal Gasket
Turn Signal Gasket, Replaces OEM # 33406-431-781
Rick's Electrics - Lithium Ion Battery Compatible Rectifier Regulator
Rick's Electrics Brand Lithium Ion Battery Compatible Style Rectifier / Regulator. Designed with a lower voltage set point (As used in Lithium Ion Batteries). This direct plug and play unit replaces OEM# 31600-MK3-000, 31600-MC7-008, 31600-MB6-630, 31600-449-831, 31600-MA1-008, 31600-KAB-901, 31600-MF2-008. This upgraded unit does not have the black signal wire as it is not needed with this unit. Not for use with standard lead acid batteries.
Ignition Switch Assembly
Ignition Switch Assembly OEM Ref # 34100-431-017 / 34100-431-027 / 34100-431-037 / 34100-431-047 / 35100-415-017 / 35100-MB9-010
Fuse Box Assembly
Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM # 38200-425-005
Fuse Box Assembly *Damaged Tabs*
*Damaged Tabs* Fuse Box Assembly Complete with 10Amp Fuses, Replaces OEM# 38200-425-005. This Fuse Box Typically has 4 Sets of Attachment Tabs on the back of the assembly used to fasten to the bike. However, several had tabs broken during transit so our loss is your gain! This unit has absolutely nothing wrong with the electrics. The unit your purchasing has damage to some or all of the tabs used to fasten the unit to your bike. Due to where it is attached all tabs should not be needed for installation. You may or may not need to find a solution such as glue/tape etc. to install but it should not pose any problems. As there is a cover over this unit if you use a little duct tape etc. nobody will ever know.
Battery Box Rubber
Battery Box Rubber, Replaces OEM# 83618-323-000 Sold Each, Order the Quantity you Require
Horn Sub Harness "A"
Horn Sub Harness "A", This is the Harness that Attaches to the Horn. Replaces OEM # 32101-438-000
Headlight Adjusting Screw & Spring Set
Headlight Adjusting Screw & Spring Set. Each Set Includes One Screw and One Spring. Replaces OEM # 33103-346-670 (Screw) and OEM # 33107-300-003 (Spring)
Oil Pressure Switch
Oil Pressure Switch, Replaces OEM # 37240-P13-013
Rick's Electrics ~ Starter Motor
Rick's Electrics Brand OEM Style Starter Motor Does Not Include the Starter Gear
Lever Safety Stop Switch
Front Clutch Lever Safety Stop Switch, Replaces OEM # 35330-413-003 This is the switch that allows the bike to start when the clutch lever is depressed.
Starter Clutch Roller Spring
Starter Clutch Roller Spring, Replaces OEM # 28125-516-030 Sold Each, Order the Quantity you Require
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Starter Motor Terminal Rubber Boot
Starter Motor Terminal (Cover) Rubber Boot. Replaces OEM # 32411-230-000
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.