Honda ► SL350 ►
-
Here’s our hand-picked list of parts and accessories for your Honda SL350 with universal parts included that match “honda sl125”►
- Honda
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Stock Type Mirror Set
Stock Type Mirror Set/2, Replaces OEM# 88110-329-730 / 88110-074-000 / 88120-329-730 / 88120-074-000 Chrome Mirrors, 8" Stem Length
Throttle Sleeeve
Throttle Sleeve
Front Fork Top Bridge / Triple Tree Washer Kit
Front Fork Top Bridge / Triple Tree Washer Kit of 2 Washers. These washers are needed in order to avoid broken top triple trees when you tighten up your fork tube clamps. Replace # OEM 53235-300-000
Sidecover Damper Rubber A
Rubber Sidecover Damper A, Replaces OEM # 17247-303-000
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Clutch Lever Perch
Clutch Lever Perch, Replaces OEM# 53172-310-010 / 53172-110-000 / 53172-310-000 Includes a 10mm Mirror Mount, for 7/8" handlebars
Clutch Lever
Clutch Lever OEM Ref # 53178-369-700 / 53190-329-010 / 53190-286-670
Brake Lever
Brake Lever OEM Ref # 53175-402-700 / 53170-216-670 / 53175-286-000 / 53170-286-670 / 53170-329-010 / 53170-369-700 / 53175-369-700
Brake Lever Perch
Brake Lever Perch, Replaces OEM# 53171-312-003 Includes a RH Thread 10mm Mirror Mount. Fits to 7/8" handlebars and includes a hole for the brake light switch.
Gear Change Rubber
Gear Change Rubber OEM Ref # 95011-400-000
Piston Pin Clips
Piston Pin Clips, 15mm (Pk/2) - Japanese made Superior Quality OEM Ref. # 94601-15000
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Ignition Coil
Ignition Coil, Replaces OEM # 30500-292-672 / 30500-312-000 / 30500-286-004 / 30500-286-007 / 30500-310-670 12 Volt Single Output Ignition Coil with spark plug wire. Primary resistance 5 Ohms. Spark plug wire is 19" long, Mounting holes are approximately 80mm (3.15") apart center to center, 6.5" blue wire with dual female bullet connector, 5.25" black/white line wire with male bullet connector. Note: If you are replacing a beige Honda coil, you will need to mount it backwards as the wires come out of it differently. Other than mounting, functionality will be the same.
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-286-010 / 22201-415-000 / 22201-ME2-000
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Tail Light Lens
Red Tail Light Lens with Amber Side Reflectors. OEM Ref # 33702-077-671
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17525-300-000
Rectifier
Rectifier with female connector, Replaces OEM# 31700-455-671 / 31700-358-305 / 31700-358-013
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Grease Fitting Nipple (Pk/2)
Grease Fitting Nipple A .45 (Pk/2). Replaces OEM # 96201-30001
Bar Switch Assembly - Right (Brake) Side
Bar Switch Assembly ~ Right (Brake) Side. Replaces OEM # 35300-319-670
Float Bowl Gasket
Float Bowl Gasket
Speedometer Cable
Speedometer Cable - Black - OEM Ref. # 44830-425-870 End to End Length 38.5" Made in Japan
Tachometer Cable
Tachometer Cable - Black - OEM Ref # 37260-KB7-010 / 37260-438-000 Made in Japan Length is 24" - Confirm this is the length you require before purchasing
Shock Absorber Joint Rubber Set/2
Shock Absorber Joint Rubber Set/2. Replaces OEM # 52484-292-000
Handlebar Clamp Set /2
Black Handlebar Clamp Set/2. These clamp the stock 7/8" handlebars to the upper triple clamp. Replaces OEM # 95014-22200
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 17534-323-300
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Rear Wheel Bearing Retainer
Rear Wheel Bearing Retainer - Brake Disc Side - Replaces OEM# 41231-286-000
Clutch Spring Set
Clutch Spring Set
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 40543-471-000 / 40543-312-010. If you require 2 adjusters purchase 2 of this part.
Seat Lock with Keys
Seat Lock with Keys, Replaces OEM # 77230-399-007 / 77230-107-711 This seat lock works perfect for the bikes listed but the locking mechanism sticks out a bit farther then the OEM type. If you have lost your old key you have to remove the seat lock bracket and assembly. This can be done with a short 10mm wrench or socket, once that's done the rest is easy.
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 18291-286-000 / 18291-286-306 Sold Each, Order the Quantity you Require
Seat Lock Bar Assembly
Seat Lock Bar Assembly, Replaces OEM# 77220-340-003 / 77220-340-011
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 18291-286-000 / 18291-286-306
Air Screw Needle O-Ring
Air Screw Needle O-Ring. 2.8mm x 1.2mm. Note: sold each, order the quantity you require
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400210850353 Please note Oil Pump Gasket Not Included
Shock Absorber Nut
Shock Absorber Nut, Used when Installing Shocks. Replaces OEM # 90309-315-000 Note: Nuts sold Each, order the quantity you require
Tachometer Cable
Tachometer Cable - Black - OEM Ref. # 37260-149-000 (700mm), 37260-KB7-010 / 37250-149-000 Made in Japan
Performance Starter Motor
Rick's Electrics Brand Performance Hot Shot Starter Motor Unit, Replaces OEM# # 31200-286-405 / 31200-286-168 / 31200-286-158. It is an upgraded 4 brush permanent magnet starter; it includes a new cable that is longer than the stock piece for easy installation.
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Steel Clutch Plate
Steel Clutch Plate B OEM Ref # 22321-KA4-700 Order the Quantity you require
Hot Shot Rectifier / Regulator
Rick's Electric Brand Hot Shot Rectifier / Regulator. Replaces OEM# 31400-292-670 / 31700-455-671 / 31700-292-008. This combination unit works with the stock stator to provide an upgraded charging system; it allows the stator to charge at full capacity 100% of the time! This is a direct plug-in combination rectifier-regulator that looks the same as the OE version & will mount in the same location as the OE rectifier for easy install. This unit is NOT compatible with lithium-ion batteries. If you have a Lithium Ion battery installed we sell a lithium ion version of this item.
Tail Light Assembly
Tail Light Assembly. Includes Brake Light Lens, Back Plate, Screws, Gasket, Wires, Connector and Dual Filament Bulb. Replaces OEM # 33700-292-671 / 33700-235-673 / 33701-300-671 / 33701-307-670 Two Bolt Back Mounting Bolt Pattern (Approx 96mm Center to Center), 2 Wires, Ready to Mount to your Bike!
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Charging Kit
Rick's Electrics Charging Kit for use with Standard Lead Acid Batteries. Kit includes both a high quality stator and a rectifier / regulator. The kit will put out approximately 150 watts and power a 55 watt headlight. This kit is NOT for use with lithium ion batteries. We sell a charging kit for lithium ion batteries as well.
Cam Chain Guide Pin
Cam Chain Guide Pin OEM Ref # 14612-286-000
Kick Stand Stopper Rubber
Kick Stand Stopper Rubber "A" - Replaces OEM# 95011-61000.
Tail Light Lens Gasket
Tail Light Lens Gasket - Replaces OEM# 33709-077-671
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Performance Rotor
Rick's Electrics Performance Hot Shot Series Rotor, Replaces OEM# 31100-286-309 / 31100-286-004. This rotor features an upgraded design and is stronger & more powerful than the OE version.
Tachometer Cable
Tachometer Cable - Black - OEM # 37260-425-000 / 37260-ME8-000 / 37260-MA5-670 / 37260-ME-000 Made in Japan
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 30204-286-004 / 30202-369-154
Fork Cap O-Ring Set/2
Fork Cap O-Ring Set of 2. 23mm x 2.8mm size. Replaces OEM # 94608-50000 X2.
Clutch Ball Retainer
Clutch Ball Retainer, Replaces OEM# 22860-286-000
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Cam Shaft Roller Collar
Cam Shaft Roller Collar - Replaces OEM # 14606-286-000
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 30203-286-004 / 30203-369-154
Steel Clutch Plate "A"
Steel Clutch Plate "A", Replaces OEM# 22311-286-000. 1 Plate Used Per Bike
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-287-004
Rear Shock Swingarm Bushing
Rear Shock Swingarm Bushing, Replaces OEM# 40548-268-000 19mm Long, 22mm OD, 10mm ID. Sold Each, Order the Quantity you Require
Cam Chain Guide
Cam Chain Guide - Replaces OEM# 14611-312-000
Custom Rear Brake Stopper Arm Strap ~ Joker Machine
Joker Machine Brand ~ Custom Rear Brake Stopper Arm Strap, Replaces OEM # 43431-286-010 / 43431-340-000 This strap is lightweight, identical length to the stock strap and really gives your bike a great custom look! High quality part CNC machined in the U.S.A.
Gas/Fuel Tank Chrome Cap
Gas/Fuel Tank Chrome Cap with Gasket and Hinge Pin (with E-Clip which Allows for easy installation). Replaces OEM # 17510-323-310
Custom Black Gas/Fuel Tank Cap ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Flip Up Billet Cap. Includes Cap with a spring loaded alloy flange, replaceable rubber gasket and alloy screw attachment. Replaces OEM # 17510-323-310 Installs easily onto the tank hinges with an alloy screw (not rivets found on the stock set-up) in minutes. Lightweight design is made from a solid block of 1" thick Billet aluminum. Works with stock style latching mechanisms (Sold Separately). High quality CNC machined cap made in the U.S.A.
Fork Dust Seals
Fork Dust Seals Set/2 35 X 53 OEM Ref # 91254-434-003 / 91254-435-003 / 51425-340-000
Cam Roller Pin
Cam Roller Pin - Replaces OEM # 14605-286-020
Side Cover Emblem Fixing Nut Pk/2
Side Cover Emblem Fixing Nut (3mm) Pk/2, Used to Attach the Side Cover Emblems. Replaces OEM # 90313-567-000 Check your bike to see the quantity you require
Rear Fuel Tank Holder Rubber
Rear Fuel Tank Holder Rubber, Replaces OEM# 17613-286-000
Front Sprocket Lock Plate Set
Front Sprocket Lock Plate with 2 Lock Plate Bolts. It's Always good to replace these when installing a new front sprocket. Replaces OEM # 23811-292-000 (Plate) and OEM # 92101-06016-0A (Bolts) X2.
Starter Motor Seal
Starter Motor Seal - 60 x 1.4 - Replaces OEM# 31206-286-158 / 31206-402-008
Fork Seals
Fork Seals Set/2 33 X 46 X 11
Honda Handlebar Pad
Honda Handlebar Pad Protect your chest and spruce up the look of your bike with a brand new handlebar pad. These will fit to 1/8" and 7/8" bars.
Honda Tin Sign
Honda Tin Sign Spruce up your garage or man cave with this 12" by 12" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo Flag
Honda Logo Flag - Features the classic Honda logo, measures 36" by 23" and includes metal stud holes in each corner for easy mounting. Will look great in any garage or shop!
Honda Logo Keychain
Honda Logo with Red Emblem - Rubber Keychain 5.5" Total Length
Honda Beanie Hat / Toque
Honda Beanie Hat / Toque. This black beanie features the classic Honda Logo on both sides. This hat is one size fits all but does fit quite large.
Honda Garage - Tin Sign
Honda Garage with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Red Honda Logo Hat
Red Honda Logo Hat Velcro Adjustable Back
Blue Honda Racing Hat
Blue Honda Racing Hat Velcro Adjustable Back
Leather Honda Logo Keychain
High Quality Leather Honda Logo Keychain with Second Logo at the Base.
Honda Logo Rubber Keychain
Honda Logo Rubber Keychain
Honda Riding Bandana / Scarf
Honda (The Power of Dreams) Riding Bandana / Scarf. This lightweight breathable bandana is perfect for riding on your bike and keeping debris away from your mouth and face.
White Honda Logo Hat
White Honda Logo Hat Velcro Adjustable Back
Honda 93 Red Hat
Honda 93 Red Hat - High Quality Hat With Beautiful Stitched Logos.
Honda Gray Trucker Hat
Honda Gray Trucker Hat With Quality Sewn on Patch Snap On Adjustable Back
Honda Wing Floor Mat
Honda Wing Floor Mat. This mat makes a great addition to any garage/shop or mancave! Measures 15.75" x 24"
Honda Logo (White Logo) - Tin Sign
Honda Logo (White Logo) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo (Red Background) - Tin Sign
Honda Logo (Red Background) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo (Black Background) - Tin Sign
Honda Logo (Black Background) with weathered looking edges - Tin Sign Spruce up your garage or man cave with this 12" by 8" Tin Sign. Includes holes in the corners for easy hanging.
Honda Logo Keychain with Fibre Background
Honda Logo Keychain with Carbon Fibre Looking Background
Honda Logo Keychain with Carbon Background
Honda Logo Keychain with Carbon Pattern Background
Honda Logo Fox Trucker Hat
Honda Logo with Fox Emblem Trucker Hat. High Quality Hat With Beautiful Stitched Honda Logo. Snap On Adjustable Back
Honda Logo HRC Trucker Hat
Honda Logo with HRC Emblem Trucker Hat. High Quality Hat With Beautiful Stitched Honda Logo. Snap On Adjustable Back
Black / Red - Honda Logo HRC Hat
Black / Red - Honda Logo with HRC Emblem Hat. High Quality Hat With Beautiful Stitched Honda Logo. Snap On Adjustable Back
Black - With White Honda Logo Hat
Black - With White Honda Logo Hat Adjustable Velcro Back