Honda ► SL350K ►
-
Here’s our hand-picked list of parts and accessories for your Honda SL350K with universal parts included that match “screws nuts bolts tools”►
- Honda
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Side Stand Pivot Bolt & Nut Set
Side Stand Pivot Bolt & Nut Set, This is the Set Used to Fasten the Side Stand in Place. Replaces OEM # 90108-283-000 (Bolt) and 94002-10000-0S (Nut).
Handlebar Clutch Lever Pivot Bolt & Nut Set
Handlebar Clutch Lever Pivot Bolt & Nut Set. This is the Set that Fastens the Clutch Lever in Place. Includes One Bolt with One Nut. Replaces OEM # 90114-310-000 (Bolt) and OEM # 94001-06200-0S (Nut).
Custom Drive Chain Adjuster Screws ~ Black ~ Joker Machine
Joker Machine Brand ~ Black Custom Type Drive Chain Adjuster Screws (Set of 2) with Gold Cadium Plated Nuts. Replace OEM # 90119-283-000 Features a CNC Machined Knob Section with 3 methods of Adjusting (By Hand with the Knurled Section, With an Open or Box Wrench on the Hex or with an Allen Wrench through the End of the Knob to the Screw). These Adjuster Screws Look Very Sharp and Improve the Look of your Bike. High Quality Made in the U.S.A.
Steering Stem Nut
Chrome Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 Note: Sold Each, order the quantity your require
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 95014-17000 / 40543-286-000. If you require 2 adjusters purchase 2 of this part.
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 40543-471-000 / 40543-312-010. If you require 2 adjusters purchase 2 of this part.
Carburetor Screw Kit
Carburetor Screw Kit (Enough For 2 Carbs) Get a new set of screws to clean up the look of your carbs! Kit Includes: 2X - Drain Screws with O-Rings 8X - 4x10 Screws w Lock Washers 8X - 4x8 Screws w Lock Washer 2X - 5x12 Screws w Lock Washers
Ignition Switch Assembly
Ignition Switch Assembly With round wire harness to switch connector. Round plug 6 Hole, 4 Wire Type. OEM Ref # 35100-303-007 / 35100-292-003 / 35100-292-013 Note: We offer an ignition switch nut tool on our site to easily loosen or tighten the ignition switch nut without causing damage to the switch
Black Steering Stem Nut ~ Joker Machine
Joker Machine Brand ~ Black Steering Stem Nut, Hex Nut Size 30mm. Replaces OEM # 90304-415-000 High quality CNC machined part made in the U.S.A.
Custom Black Gas/Fuel Tank Cap Latch Assembly ~ Joker Machine
Joker Machine Brand ~ Custom Black Gas/Fuel Tank Cap Latch Assembly, Includes Black Latch, Return Spring and Alloy Screw attachment with nut. A fully CNC machined, billet aluminum alternative to the discontinued cast thumb latches. Install is easily made with the provided alloy screw attachment with nut. Much more durable and stronger than the original die-cast piece. High quality CNC machined part made in the U.S.A. Ties in great with our Custom Black Gas/Fuel Tank Cap (#73-1156)
Joker Machine Magnetic Oil Drain Plug
Joker Machine Magnetic Oil Drain Plug with O-Ring, Replaces OEM# 90013-312-000. High quality made from 6061 billet aluminum. High power rare earth neodymium-iron boron magnet pressed into the body that exceptionally grabs steel debris from your tank and motor. M33.7 - 1.5mm thread pitch. Installs with a 19mm socket. - 45mm outside diameter and 19mm off the case.
Stock Type Reflector
Stock Type Screw on Reflector, 6mm thread. Replaces OEM # 33741-340-670
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Custom Brake Rod Adjuster Knob ~ Joker Machine
Joker Machine Brand ~ Custom Brake Rod Adjuster Knob, Replaces OEM # 95015-42000 Gives your bike a great custom look while refining the quality of your brake adjuster knob! Makes for super easy brake adjustments due to the choice of a knurled outside knob and a hex nut feature all in one. High quality CNC machined part, made in the U.S.A.
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes