Honda ► TL250 ►
-
Here’s our hand-picked list of parts and accessories for your Honda TL250►
- Honda
Seat Rubber "B"
Seat Setting Rubber "B". This is one of the Rubber Settings Under the Seat. Replace those old worn Rubbers with a brand new one! Replaces OEM # 77205-286-000 Order the Quantity of Seat Rubber "B" your Bike Requires
Clutch Lever
Clutch Lever OEM Ref # 53178-399-700 / 360-700-000 / 360-467-000 / 360-401-651 / 53178-401-651 / 53178-467-000 / 53178-360-700
Brake Lever
Brake Lever OEM Ref # 53175-467-000 / 53170-413-670 / 53175-402-700 / 53175-360-700 / 53175-399-700
Brake Lever Perch
Brake Lever Perch, Replaces OEM# 53171-429-770 / 53171-376-000 No Mirror mount or brake switch mounting hole Fits to 7/8" handlebars
Clutch Lever Perch
Clutch Lever Perch, Replaces OEM# 53172-429-770 / 53172-376-000 Fits: 7/8" Handlebars - No Mirror Mount
Ignition Coil with Condenser
Ignition Coil with Condenser, Replaces OEM# 30500-950-405 6 Volt, 5.4k Ohm.
Handlebar Rubber Cover Set/2
Handlebar Rubber Cover Set/2 - Replaces OEM# 53176-329-000 (Right Side), 53179-329-000 (Left Side) One rubber for the left and one for the right side per set.
Denso Ignition Contact Points
Contact Points (1pc.) - Replaces OEM # 30202-107-004 / 30202-216-004 / 30202-107-154 These points are for Nippondenso ignitions Only. They are NOT for Hitachi or Kokusan Ignitions. Please check which type you have before ordering. Honda used different ignition systems on some of the same years of bikes.
Carb Float
Brass Carb Float with Pin - Replaces OEM# 16013-286-014 Fits VM29/33 Smoothbores & most OEM CV/VM Mikuni carbs Used on Yamaha & Kawasaki up to 1980 and some Honda's
Cotter Valve / Valve Keeper
Cotter Valve / Valve Keeper, Replaces OEM# 14781-107-003 / 14781-107-020. 2 Used For Each Valve Spring. Sold Each, Order the Quantity you Require
Flange Knock Bolt (Set/2)
Flange Knock Bolt (Set/2). These Bolts Fasten to the Cam Sprocket. Replaces OEM # 90082-HA0-000
Special Oil Filter Rotor Washer
Special Angled Oil Filter Rotor Washer (16mm), Replaces OEM# 90481-292-000
Clutch Center Nut Removal Tool
Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.
Clutch Center Nut Removal Tool ~ Premium
Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension bar, Diameter 20 x 24.
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16011-302-004 / 16011-375-004
Fuel Petcock Gasket
Fuel Petcock Gasket, Replaces OEM# 16957-ZE1-812 / 16955-028-004 / 16955-011-010
Clutch Cover Screw Set
Clutch Cover Screw Set. Includes all 3 Screws needed to fasten the Clutch Cover. Replaces OEM # 93700-06016-0B X3.
Cam Chain
Cam Chain 219T x 94 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 14401-286-003 / 14401-410-003
Fork Dust Boot Set
Fork Seal Dust Boots (Set/2). 33mm Size, Replaces OEM # 91254-413-881
Clutch Tab Washer
Clutch Tab Washer, 16mm Size, Replaces OEM # 90431-292-000
Valve Stem Seal
Valve Stem Seal. Replaces OEM # 12209-333-005 / 12209-333-005 Sold Each - Order the Quantity you Require