Honda ► VF500C ►
-
Here’s our hand-picked list of parts and accessories for your Honda VF500C with universal parts included that match “1”►
- Honda
Long Stem Air Glide Mirror Set
Long Stem Chrome Billet Aluminum Oval Air Glide Mirror Set. left hand thread adapter included for Yamaha right-side perch. These mirrors will fit most Honda, Kawasaki, Suzuki & Yamaha's with a 10mm mounting hole. 10mm thread, Stem 6.9" total length, Mirror 5 1/8" wide, 2 5/8" tall, 5/8" deep.
Ignition Coil ~ 3 Ohm
Dual Tower Performance High Output Ignition Coil 3.3 OHM Primary resistance ignition coil, 15K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 3 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Chopper T Handlebar - Chrome
Chopper T Handlebar - Chrome Bar Diameter - 7/8" - 22mm, Length - 27 3/4" - 705mm, Pull Back - 4 1/2" - 114mm, Inner Rise - 7" - 178mm, End Rise - 7" - 178mm, Center Width - 5" - 127mm, Base Width - 7" - 178mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
Chopper T Handlebar - Black
Chopper T Handlebar - Black Bar Diameter - 7/8" - 22mm, Length - 27 3/4" - 705mm, Pull Back - 4 1/2" - 114mm, Inner Rise - 7" - 178mm, End Rise - 7" - 178mm, Center Width - 5" - 127mm, Base Width - 7" - 178mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
Handlebar
Ape Hanger Handlebar - Chrome Bar Thickness - 22mm - 7/8", Length - 838mm - 33", Pull Back - 203mm - 8", Inner Rise - 305mm - 12", End Rise - 248mm - 9 3/4", Center Width - 127mm - 5", Base Width - 228mm - 9", Control Length - 216mm - 8 1/2", Drilled - NO
Handlebar - Black
Ape Hanger Handlebar - Gloss Black Bar Thickness - 22mm - 7/8", Length - 838mm - 33", Pull Back - 203mm - 8", Inner Rise - 305mm - 12", End Rise - 248mm - 9 3/4", Center Width - 127mm - 5", Base Width - 228mm - 9", Control Length - 216mm - 8 1/2", Drilled - NO
Bearing Packer
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Red Reflective License Plate Bolts (Pk/2)
Red Reflective License Plate Bolts (Pk/2). Bolts include springs and wing nuts. 1" round outer diameter, 3/4" long mounting stud. Spring tension keeps them from coming loose. Do not over tighten as it will pull the back out or pop the lens off, order 2 Packs of 2 for a full set of 4.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
JIS Screw Bit Set
JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3. Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face. It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!
Micro Custom Speedometer-KPH ~ Black Face Plate
Micro (1.9") Chromed Custom Type Kilometers Per Hour (KM/H) Speedometer with Black face plate. Includes LED illumination and mounting plate, requires mounting brackets (03-0740, 03-0741, 03-0762 or 03-0763) to mount to handlebars. Face dial ranges from 0-220KM/H. The ratio of this Speedometer is 60MPH=2240 RPM. Note: These are not stock type replacement speedometers, Please ensure this is the correct ratio for your bike.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
HandleBar
HandleBar European Type Chrome Bar Diameter - 7/8" - 22mm, Length - 30 1/4 - 768mm, Pull Back - 5" - 127mm, Inner Rise - 3 3/8" - 86mm, End Rise - 3" - 76mm, Center Width - 5" - 127mm, Base Width - 7 3/4" - 197mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
HandleBar
HandleBar Suzuki GS Type Chrome Bar Diameter - 7/8" - 22mm, Length - 30" - 762mm, Pull Back - 6" - 152mm, Inner Rise - 6 3/4" - 171mm, End Rise - 9" - 228mm, Center Width - 5 1/2" - 140mm, Base Width - 8" - 203mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
Handlebar - Black
European Type Bar - Black. Bar Diameter - 7/8" - 22mm, Length - 30 1/4 - 768mm, Pull Back - 5" - 127mm, Inner Rise - 3 3/8" - 86mm, End Rise - 3" - 76mm, Center Width - 5" - 127mm, Base Width - 7 3/4" - 197mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
Handlebar
Dirtbike Custom Type Bar - Chrome. Bar Diameter - 7/8" - 22mm, Length - 31 3/4" - 806mm, Pull Back - 4" - 102mm, Inner Rise - 4 1/4" - 108mm, End Rise - 6 3/4" - 171mm, Center Width - 5" - 127mm, Base Width - 8" - 203mm, Control Length - 9" - 228mm, Drilled - NO Note: Not Drilled for wires
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
TC Bros. Universal Linkage Kit
TC Bros. Brand Universal Linkage Kit for all TC Bros. Forward Control Kits. The rods/tubes will need to be cut to fit your application. Kit includes, Two 24" Long 5/16" Threaded Rods, Four 5/16" Ball Joints, Two 5/16" ID x 1/2" OD Steel Tubes* (to cover rod threads and increase rigidity), Eight 5/16" Jam Nuts, Four Nylock Nuts and Four Flat Washers. This Set is needed for all the forward control kits we carry
Feeler Gauge Set
Feeler Gauge Set - Metric Feeler Gauge Set for setting valve and contact point clearances. 20pc Set (marked in metric sizes only). 0.05mm. - (.002") 0.55mm. - (0.22") 0.10mm. - (.004") 0.60mm. - (0.24") 0.15mm. - (.006") 0.65mm. - (0.26") 0.20mm. - (.008") 0.70mm. - (0.28") 0.25mm. - (.010") 0.75mm. - (0.30") 0.30mm. - (.012") 0.80mm. - (0.32") 0.35mm. - (.014") 0.85mm. - (0.34") 0.40mm. - (.016") 0.90mm. - (0.36") 0.45mm. - (.018") 0.95mm. - (0.38") 0.50mm. - (0.20") 1.00mm. - (0.40")