Honda ► VT750C ►
-
Here’s our hand-picked list of parts and accessories for your Honda VT750C with universal parts included that match “screws nuts bolts tools”►
- Honda
![Honda VT750C Piston Pin Puller](/images/parts/100/35-0090.jpg)
Piston Pin Puller
Piston Pin Puller Fits Piston Sizes from 40mm (1 5/8") to 100mm (4") and Piston Pins From 12mm to 17mm Tool has 2 threaded steps 12mm and 17mm. Diameter of the rod that goes through the piston pin is 8.5mm..
![Honda VT750C Valve Spring Compressor](/images/parts/100/35-0115.jpg)
Valve Spring Compressor
Valve Spring Compressor Kit in a Plastic Storage Case. Includes adapter sizes 16mm, 19mm, 23mm, 25mm and 30mm.
![Honda VT750C Oil Filter Wrench](/images/parts/100/35-0121.jpg)
Oil Filter Wrench
Oil Filter Wrench Wafer-Thin For GL1500 Goldwings Also Works On Many other Honda/Yamaha/Kawasaki Models
![Honda VT750C Fork Oil Level Gauge](/images/parts/100/35-1084.jpg)
Fork Oil Level Gauge
Fork Oil Level Gauge For Adjusting The Oil Level On All Forks. Adjustable Ring Measures Oil Levels From 0-300mm in 50mm Increments. 60ml Capacity Syringe Adjusts Fluid Levels.
![Honda VT750C Leakdown Tester](/images/parts/100/35-1377.jpg)
Leakdown Tester
Leakdown Tester Dual Guage Tester Complete With 25" hose with Stepped adaptor One Dial Guage Reads 0-100PSI, Other Reads 0-100 Percent
![Honda VT750C Feeler Gauge Set](/images/parts/100/35-1766.jpg)
Feeler Gauge Set
Feeler Gauge Set 45 Degree Ends- Metric Feeler Gauge Set for setting valve clearances. 9pc. Set (marked in metric sizes only). 0.229mm. - (.009") 0.381mm. - (.015") 0.406mm. - (.016") 0.432mm. - (.017") 0.457mm. - (.018") 0.483mm. - (.019") 0.508mm. - (.020") 0.533mm. - (.021") 0.660mm. - (.026")
![Honda VT750C Feeler Gauge Set](/images/parts/100/35-1767.jpg)
Feeler Gauge Set
Feeler gauge set with 45 degree ends. Includes Sizes - .008", .010", .012", .013", .014", .015", .016", 018", .019", .020", .025", .026" Marked in Metric and Inch sizes.
![Honda VT750C Feeler Gauge Set](/images/parts/100/35-1768.jpg)
Feeler Gauge Set
Feeler Gauge Set - Metric Feeler Gauge Set for setting valve and contact point clearances. 20pc Set (marked in metric sizes only). 0.05mm. - (.002") 0.55mm. - (0.22") 0.10mm. - (.004") 0.60mm. - (0.24") 0.15mm. - (.006") 0.65mm. - (0.26") 0.20mm. - (.008") 0.70mm. - (0.28") 0.25mm. - (.010") 0.75mm. - (0.30") 0.30mm. - (.012") 0.80mm. - (0.32") 0.35mm. - (.014") 0.85mm. - (0.34") 0.40mm. - (.016") 0.90mm. - (0.36") 0.45mm. - (.018") 0.95mm. - (0.38") 0.50mm. - (0.20") 1.00mm. - (0.40")
![Honda VT750C Feeler Gauge Set](/images/parts/100/35-1769.jpg)
Feeler Gauge Set
Feeler Gauge Set - Metric/Inch Feeler Gauge Set for setting valve and contact point clearances. 32pc Set (marked in metric and inch sizes). 0.04mm. - (.0015") 0.05mm. - (.002") 0.06mm. - (.0025") 0.08mm. - (.003") 0.10mm. - (.004") 0.13mm. - (.005") 0.15mm. - (.006") 0.20mm. - (.008") 0.23mm. - (.009") 0.25mm. - (.010") 0.28mm. - (.011") 0.30mm. - (.012") 0.33mm. - (.013") 0.35mm. - (.014") 0.38mm. - (.015") 0.40mm. - (.016") 0.43mm. - (.017") 0.45mm. - (.018") 0.48mm. - (.019") 0.50mm. - (.020") 0.53mm. - (.021") 0.55mm. - (.022") 0.58mm. - (.023") 0.63mm. - (.025") 0.65mm. - (.026") 0.70mm. - (.028") 0.75mm. - (.030") 0.80mm. - (.032")
![Honda VT750C Locknut Wrench](/images/parts/100/35-3002.jpg)
Locknut Wrench
Locknut Wrench 1/2" Drive, 6 Lug 42mm OD & 35mm ID Fits Cogged Locknuts Such As Steering Heads & Some Filters/Clutches
![Honda VT750C Tappet T-Socket Wrench](/images/parts/100/35-4210.jpg)
Tappet T-Socket Wrench
Tappet T-Socket Wrench 10mm
![Honda VT750C 39mm Fork Seal Driver](/images/parts/100/35-4298.jpg)
39mm Fork Seal Driver
39mm High quality carbon steel fork seal driver with split design. Use this for easy installation of 39mm fork seals on either conventional or inverted forks.
![Honda VT750C 35/36mm Fork Seal Driver](/images/parts/100/35-4299.jpg)
35/36mm Fork Seal Driver
35/36mm High quality carbon steel fork seal driver with split design. Use this for easy installation of 35 or 36mm fork seals on either conventional or inverted forks.
![Honda VT750C Fork Seal Driver](/images/parts/100/35-4300.jpg)
Fork Seal Driver
43mm High quality carbon steel fork seal driver with split design. Use this for easy installation of 43mm fork seals on either conventional or inverted forks.
![Honda VT750C Fork Seal Driver](/images/parts/100/35-4500.jpg)
Fork Seal Driver
45mm High quality carbon steel fork seal driver with split design. Use this for easy installation of 45mm fork seals on either conventional or inverted forks.
![Honda VT750C Fork Seal Driver](/images/parts/100/35-4950.jpg)
Fork Seal Driver
49/50mm High quality carbon steel fork seal driver with split design. Use this for easy installation of 49mm or 50mm fork seals on either conventional or inverted forks.
![Honda VT750C Shock Ring Wrench](/images/parts/100/35-5033.jpg)
Shock Ring Wrench
Ring Wrench to adjust shock preload. Fits: Our shock sets and many other aftermarket shocks.
![Honda VT750C Spin On Oil Filter Wrench](/images/parts/100/35-9022.jpg)
Spin On Oil Filter Wrench
Spin On Oil Filter Wrench Removes 63-98mm In Diameter - 3/8" Drive
![Honda VT750C Strap Wrench](/images/parts/100/35-9024.jpg)
Strap Wrench
Strap Wrench Fits 29-160mm Ideal For Holding Fork Tubes
![Honda VT750C Compression Tester](/images/parts/100/35-9030.jpg)
Compression Tester
Compression Tester Includes Adaptors to Fit 10mm, 12mm, 14mm & 18mm Plug Holes
![Honda VT750C Image Scope](/images/parts/100/35-9096.jpg)
Image Scope
Professional Flexible Fiber Optic Image Scope for inspecting engine internal parts. 18" long wand with a 6mm (1/4") OD tip. Image resolution is 7,400 pixels. Packed in a blow mold case with handle jacket and extra Xenon Bulbs and 2 AA batteries.
![Honda VT750C Shock Pump](/images/parts/100/35-9107.jpg)
Shock Pump
Shock Pump 300 PSI Rear Shocks Or Front Fork Suspensions
![Honda VT750C Deluxe Fork Seal Driver Set](/images/parts/100/35-9109.jpg)
Deluxe Fork Seal Driver Set
Deluxe Fork Seal Driver Set. This set includes 9 high quality carbon steel fork seal drivers with split design. Use these for easy installation of most fork seals on either conventional or inverted forks. Set Contains plastic storage case and the following drivers. -35/36mm driver -39mm driver -41mm driver -43mm driver -45mm driver -46/47mm driver -48mm driver -49/50mm driver -54mm driver
![Honda VT750C Fork Cap Wrench ~ 35MM Size](/images/parts/100/35-9113.jpg)
Fork Cap Wrench ~ 35MM Size
Fork Cap Wrench ~ 35MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 35MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
![Honda VT750C Fork Cap Wrench ~32MM Size](/images/parts/100/35-9114.jpg)
Fork Cap Wrench ~32MM Size
Fork Cap Wrench ~ 32MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 32MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
![Honda VT750C Fork Cap Wrench ~30MM Size](/images/parts/100/35-9115.jpg)
Fork Cap Wrench ~30MM Size
Fork Cap Wrench ~ 30MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 30MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
![Honda VT750C Fork Cap Wrench ~24MM Size](/images/parts/100/35-9116.jpg)
Fork Cap Wrench ~24MM Size
Fork Cap Wrench ~ 24MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 24MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
![Honda VT750C Steering Race Remover 25-35mm](/images/parts/100/35-9123.jpg)
Steering Race Remover 25-35mm
Steering Head Bearing Race Remover, Range 25-35mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 25mm to 35mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
![Honda VT750C Steering Race Remover 35-55mm](/images/parts/100/35-9124.jpg)
Steering Race Remover 35-55mm
Steering Head Bearing Race Remover, Range 35-55mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 35mm to 55mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
![Honda VT750C Impact Driver Set](/images/parts/100/35-0095.jpg)
Impact Driver Set
Impact Driver Set Heavy Duty Impact Driver With Slip Resistant Rubber Grip Comes with 6 Piece Bit Set & Case 1/2" Drive, Can also be used with 1/2" Drive Socket
![Honda VT750C Replacement Bit Set](/images/parts/100/35-0107.jpg)
Replacement Bit Set
Replacement Bit Set 1 1/2" Standard Driver Bit Set Fits 35-0106 & 35-0095 Impact Drivers Contains 2 Phillips & 2 Slotted Bits
![Honda VT750C Replacement Bit Set](/images/parts/100/35-0110.jpg)
Replacement Bit Set
Replacement Bit Set 3" Long Driver Bit Set Fits 35-0106 & 35-0095 Impact Drivers Contains 2 Phillips & 2 Slotted Bits
![Honda VT750C Snap Ring Plier Set](/images/parts/100/35-0114.jpg)
Snap Ring Plier Set
Snap Ring Plier Set Removes Internal or External Snap Rings Includes 2 Straight & 2 Angled Tips
![Honda VT750C T-Handle Wrench](/images/parts/100/35-0131.jpg)
T-Handle Wrench
T-Handle Wrench 5mm Allen
![Honda VT750C Metal Funnel](/images/parts/100/35-8040.jpg)
Metal Funnel
Metal Funnel Comes With 14" Flexible/Detachable Metal Nozzle
![Honda VT750C Flexible Magnet](/images/parts/100/35-9036.jpg)
Flexible Magnet
Flexible Magnet 23" Long Flex Rod With Magnetic Tip Lifts Up To 3.5Lbs
![Honda VT750C Graduated Cylinder](/images/parts/100/35-2210.jpg)
Graduated Cylinder
250 ml Graduated Cylinder 250cc (1/4 Liter) plastic Graduated Cylinder for accurate measuring of fork oil and other fluids.
![Honda VT750C Graduated Cylinder](/images/parts/100/35-2211.jpg)
Graduated Cylinder
500ml Graduated Cylinder 500cc (1/2 Liter) plastic Graduated Cylinder for accurate measuring of fork oils and other fluids.
![Honda VT750C Graduated Cylinder](/images/parts/100/35-2212.jpg)
Graduated Cylinder
Graduated Cylinder 1,000cc (1 Liter) plastic Graduated Cylinder for accurate measuring of fluids. 1 US Quart = 946cc (946ml.)
![Honda VT750C Fluid Hose Clamp](/images/parts/100/35-9117.jpg)
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.