Kawasaki ►
-
Pick your Kawasaki motorcycle from the list below►
- Kawasaki
Nylock Nut
Nylock Nut Pk/10 Plated Finish Size: 10mm
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Rectangular Magnetic Parts Dish
Rectangular Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 9.5" Length, 5.5" Width, 1.1" Height.
Terminal Crimping Tool
Metric Terminal Crimper Tool. Includes sizes 14-16, 14-18, 18-20, 20-24 and 22-24. Professionally Crimps like factory originals. This tool can be used with flag type terminals.
Brush Cleaning Tool
Blue Chain Cleaning Brush/ Gear Cleaner Tool.
Chain Alignment Tool
Chain Alignment Tool. This tool provides an easy way to verify your chain is aligned properly to the front and rear sprockets after rear wheel or chain maintenance. Simply clamp this tool on the rear sprocket with the rod pointing to the front sprocket. With the rod as your guide, make visual alignment then adjust the chain adjusters as needed to correct alignment.
Hex Axle Tool
Universal Hex Axle Tool, Heavy duty Suitable for shop use. Sizes 17, 19, 22, 24. 3/8 Drive on both ends Made with high quality heat treated steel.
Valve Shim Tool
Valve Shim Tool Suz GS550/750/850/1000
Valve Shim Tool
Valve Shim Tool Honda CBX, CB750/900
Clutch Holding Tool
Clutch Holding Tool Adjustable Vise Grip Style Clutch Basket & Sprocket Holder Tool
Piston Ring Tool
Piston Ring Tool with plastic storage case. This tool is designed to prevent ring breakage during cylinder installation. This tool can be easily removed after cylinder is in position. Comes with 4 rings to accept the smallest triple to the largest single cylinder engines. Fits 40-85mm sizes.
Red Reflective License Plate Bolts (Pk/2)
Red Reflective License Plate Bolts (Pk/2). Bolts include springs and wing nuts. 1" round outer diameter, 3/4" long mounting stud. Spring tension keeps them from coming loose. Do not over tighten as it will pull the back out or pop the lens off, order 2 Packs of 2 for a full set of 4.
Hex Head Nut
Hex Head Nut Pk/100 Plated Finish Size: 6mm
Hex Head Nut
Hex Head Nut Pk/100 Plated Finish Size: 8mm
Hex Head Nut
Hex Head Nut Pk/10 Plated Finish Size: 10mm
Hex Head Nut
Hex Head Nut Pk/10 Plated Finish Size: 12mm
ISO Flange Nut
ISO Flange Nut Pk/10 Std. Pitch - Steel Plated Size: 5mm
ISO Flange Nut
ISO Flange Nut Pk/10 Std. Pitch - Steel Plated Size: 6mm
ISO Flange Nut
ISO Flange Nut Pk/10 Std. Pitch - Steel Plated Size: 8mm
ISO Flange Nut
ISO Flange Nut Pk/10 Std. Pitch - Steel Plated Size: 10mm
ISO Flange Nut
ISO Flange Nut Pk/10 Std. Pitch - Steel Plated Size: 12mm
ISO Cap Nut
ISO Cap Nut Pk/10 Plated Finish Size: 6mm
ISO Cap Nut
ISO Cap Nut Pk/10 Plated Finish Size: 8mm
ISO Cap Nut
ISO Cap Nut Pk/10 Plated Finish Size: 10mm
ISO Cap Nut
ISO Cap Nut Pk/10 Plated Finish Size: 12mm
Hex Head Nut
Hex Head Nut Pk/100 Plated Finish Size: 5mm
Metric Tap & Die Set
Metric Tap & Die Set 39pc Set Includes Pitch Gauge, Die Holder, 2 Tap Wrenches, Screw Driver, Metric Taps: M3 X 0.5 M3 X 0.6 M4 X 0.75 M4 X 0.7 M5 X 0.8 M5 X 0.9 M6 X 1.0 M6 X 0.75 M7 X 0.75 M7 X 1.0 M8 X 1.0 M8 X 1.25 M10 X 1.25 M10 X 1.5 M12 X 1.25 M12 X 1.5 1/8NPT X 27 Includes 17 Dies to Match the 17 Tap Sizes Listed.
Drive Chain Riveter Tool
Drive Chain Riveter Tool Rivets High Strength Rear Drive Chain Rivet Links With Hollow Pin Ends on Many DID Brand Chains.
Replacement Pin For Riveter Tool
Replacement Rivet Pin For Drive Chain Riveter Tool (35-0006)
Steering Bearing Installation Tool
Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly any lower bearing. Use with a soft faced hammer.
Chain Press Assembly Tool
Chain Press Assembly Tool Used to Press On Sideplates on rivet or clip rear drive chains
Spark Plug Gapping Tool
Circular Spark plug gap tool. Marked in thousandths of an inch and millimeters.
Brake Caliper Piston Tool
Brake Caliper Piston Tool Holding/Detaching Tool For Brake Calipers. Grabs Brake Caliper Pistons Internally So Seized Pistons Can Be Worked Loose From The Caliper.
Tappet Adjuster Tool Set
Tappet Adjuster Tool Set Small 4 Stroke Engines Includes 8mm, 9mm, 10mm Sockets 1 Adjuster 1/8" (3mm) Square Size
Vacuum Brake Bleeder Tool
Vacuum Brake Bleeder Tool *Not For Use With Speed Bleeders*
Tire Valve Stem Tool
Tire Valve Stem Tool Core Removal & Repair Tool
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from 0.45mm to 1.5mm.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Vintage Motorcycle Tool Set
Vintage Motorcycle Tool Set. Have you lost the original tool set that came with your motorcycle? Well, we have a great alternative for you! This 8 pc set features many of the same tools that came with your bikes stock tool kit. To check out the exact contents included check out the picture. All contained within a durable pouch. Features Wrenches 8/10, 12/14 and 14/17 Note: These may not be 100% identical to your bikes OEM tool kit (check the photo for differences) but are very similar and several of the tools are likely identical. A great option at an amazing price!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Stud Extractor 6-12mm
Stud Extractor 3/8" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (6-12mm)
Lens Screw
Lens Screws Pk/10 ISO Std. Pitch - Steel Plated Size: 3 x 25mm
Lens Screw
Lens Screws Pk/10 ISO Std. Pitch - Steel Plated Size: 4 x 25mm
Lens Screw
Lens Screws Pk/10 ISO Std. Pitch - Steel Plated Size: 4 x 30mm
Lens Screw
Lens Screws Pk/10 ISO Std. Pitch - Steel Plated Size: 4 x 35mm
Flathead Screw
Flathead Screw Pk/10 Size: 5 x 25mm
Flathead Screw
Flathead Screw Pk/10 Size: 5 x 30mm
Flathead Screw
Flathead Screw Pk/10 Size: 6 x 20mm
Flathead Screw
Flathead Screw Pk/10 Size: 6 x 25mm
Flathead Screw
Flathead Screw Pk/10 Size: 6 x 30mm