Kawasaki ► H2 ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki H2►
- Kawasaki
Engine Oil Seal Kit
Engine Oil Seal Kit
Clutch Pushrod Seal
Clutch Pushrod Seal OEM Ref # 92050-025
Stock Type Shock Absorber Set
Stock Type Designed Shock Absorber Set without Reflectors. Replaces OEM # 45014-056 and 45014-096 325mm Eye to Eye Length. All chrome with gray plastic inner sleeve to protect the damper rod. Top bushing is 14mm, bottom bushing is 10mm.
Clutch Lever
Clutch Lever OEM Ref # 46092-015/014 / 46092-005
Brake Lever
Brake Lever OEM Ref # 43029-003 / 43029-002 / 43029-004 / 43029-1002
Tail Light Lens
Tail Light Lens, Replaces OEM # 23026-022
Tail Light Lens
Tail Light Lens, Replaces OEM # 23026-023
Turn Signal Lamp
Turn Signal Lamp - Chrome 2-Wire Front or Rear
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 23048-012 / 23048-1024
Rear Turn Signal Lamp ~ 1 Wire Type
Rear Turn Signal Lamp ~ 1 Wire Single Filament Type Replaces OEM# 23040-029
Ground Collar & Mounting Rubbers
Signal Lamp/Headlamp Ground Collar & Matching Mounting Rubbers OEM Ref # 23076-001 / 23076-005 / 23066-001 / 23066-015 / 23066-005 / 23066-016
Rear Spoke & Nipple Set
Rear Spoke & Nipple Set. 20 Inner Spokes 4.00-3.50X142mm Rim ( OEM # 41027-043 ), 20 Outer Spokes 4.00-3.50x141mm Rim ( OEM # 41028-057 ) with Nipples. Clear Zinc Plated Spokes and Gold Zinc Plated Nipples.
Front Spoke & Nipple Set
Front Spoke & Nipple Set. 20 Inner Spokes 4.00-3.50X176mm Rim ( OEM # 41027-042 ), 20 Outer Spokes 4.00-3.50x176.5mm Rim ( OEM # 41028-041 ) with 40 Slot Type Nipples. Clear Zinc Plated Spokes and Gold Zinc Plated Nipples.
Ignition Coil
Replacement Ignition Coil, Replaces OEM # 21121-064 These appear slightly different from the factory coil packs, but are 100% compatible. The H1 ran several different coils depending on the model. Check this is the one you need before purchasing. Sold individually, as shown in photo.
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product # P400250850703
Chrome Non-Locking Gas Cap
Chrome Non-Locking Gas Cap with Hook and Spring, Replaces OEM# 51048-007
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-008
Wire Harness
Main Wire Harness Loom - OEM Ref. # 26001-058 NOTE: These fit model years and type listed, other years and types of motorcycles use a different OEM part number (there is a difference!).
Fork Seals
Fork Seals Set/2 35 X 48 X 10.5/11
Fork Seals
Fork Seals Set/2 36 X 48 X 10.5
Fork Seal Washer Circlip Set
A set of two washers and two circlips that hold the fork seals on the 36mm forks. Replaces OEM # 44044-012 / 44043-044
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 44010-021 / 44010-018
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 40 x 62 x 7
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal 25 x 40 x 6
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 33033-009 / 90386-22018 Note: These Replace the factory plastic OEM Type Bushings.
Ribbed Brake Master Cylinder Dust Boot
Ribbed Brake Master Cylinder Dust Boot, Replaces OEM# 43069-001
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 180mm Width: 35mm OEM Ref # 41048-016
Clutch Plate
Clutch Plate 6 Pieces Required OEM Ref # 13088-015 / 13088-034 / 13088-1002 / 13088-1008 / 13088-1057 / 21441-20A02
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16030-005
Left Side Brake Hose Bracket
Left Side Brake Hose Bracket with Rubber Grommet, Replaces OEM# 43063-001 / 43064-001
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 51059-008