Kawasaki ► H2 ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki H2 with universal parts included that match “1”►
- Kawasaki
Rear Turn Signal Lamp ~ 1 Wire Type
Rear Turn Signal Lamp ~ 1 Wire Single Filament Type Replaces OEM# 23040-029
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 44010-021 / 44010-018
Wheel Seal Kit
Front Wheel Seal Kit 1 Seal 25 x 40 x 6
Chrome Non-Locking Gas Cap
Chrome Non-Locking Gas Cap with Hook and Spring, Replaces OEM# 51048-007
Clutch Pushrod Seal
Clutch Pushrod Seal OEM Ref # 92050-025
Stock Type Shock Absorber Set
Stock Type Designed Shock Absorber Set without Reflectors. Replaces OEM # 45014-056 and 45014-096 325mm Eye to Eye Length. All chrome with gray plastic inner sleeve to protect the damper rod. Top bushing is 14mm, bottom bushing is 10mm.
Ignition Coil
Replacement Ignition Coil, Replaces OEM # 21121-064 These appear slightly different from the factory coil packs, but are 100% compatible. The H1 ran several different coils depending on the model. Check this is the one you need before purchasing. Sold individually, as shown in photo.
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-008
Fork Seal Washer Circlip Set
A set of two washers and two circlips that hold the fork seals on the 36mm forks. Replaces OEM # 44044-012 / 44043-044
Wheel Seal Kit
Rear Wheel Seal Kit 1 Seal 40 x 62 x 7
Front Spoke & Nipple Set
Front Spoke & Nipple Set. 20 Inner Spokes 4.00-3.50X176mm Rim ( OEM # 41027-042 ), 20 Outer Spokes 4.00-3.50x176.5mm Rim ( OEM # 41028-041 ) with 40 Slot Type Nipples. Clear Zinc Plated Spokes and Gold Zinc Plated Nipples.
Rear Brake Shoes
Rear Brake Shoes Pk/2 Diameter: 180mm Width: 35mm OEM Ref # 41048-016
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 51059-008
Left Side Brake Hose Bracket
Left Side Brake Hose Bracket with Rubber Grommet, Replaces OEM# 43063-001 / 43064-001
Rear Spoke & Nipple Set
Rear Spoke & Nipple Set. 20 Inner Spokes 4.00-3.50X142mm Rim ( OEM # 41027-043 ), 20 Outer Spokes 4.00-3.50x141mm Rim ( OEM # 41028-057 ) with Nipples. Clear Zinc Plated Spokes and Gold Zinc Plated Nipples.
Ground Collar & Mounting Rubbers
Signal Lamp/Headlamp Ground Collar & Matching Mounting Rubbers OEM Ref # 23076-001 / 23076-005 / 23066-001 / 23066-015 / 23066-005 / 23066-016
Tail Light Lens
Tail Light Lens, Replaces OEM # 23026-022
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16030-005
Brake Lever
Brake Lever OEM Ref # 43029-003 / 43029-002 / 43029-004 / 43029-1002
Swing Arm Bushing Set
Swing Arm Bushing Set OEM Ref # 33033-009 / 90386-22018 Note: These Replace the factory plastic OEM Type Bushings.
Ribbed Brake Master Cylinder Dust Boot
Ribbed Brake Master Cylinder Dust Boot, Replaces OEM# 43069-001
Clutch Lever
Clutch Lever OEM Ref # 46092-015/014 / 46092-005
Tail Light Lens
Tail Light Lens, Replaces OEM # 23026-023
Turn Signal Lamp
Turn Signal Lamp - Chrome 2-Wire Front or Rear
Turn Signal Replacement Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 23048-012 / 23048-1024
Fork Seals
Fork Seals Set/2 36 X 48 X 10.5
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle
Universal 1" Push/Pull Harley Style Chrome Twist Grip Throttle Assembly. Chromed aluminum housing with plastic throttle tube, pre-installed throttle assembly grip. Throttle is 5 1/4" long over all. Throttle tube is 4" long. Housing is 2" in diameter. Fits: 1" handle bars. For use with dual cable set ups.
CNC Machined Black Anodized 1/4" Fuel Filter w Clips
CNC Machined Aluminum Fuel Filter with 2 Clips, Black Anodized Type with Cleanable and Reuseable Brass Filter Element. 3" Long, 1/4" Fitting.
90 Degree Bronze Inline Fuel Filter ~ 1/4"
90 Degree Inline Fuel Filter with 1/4" Fitting. Features a premium bronze porous cleanable filter.
Chrome Bungee Nut Set/2 ~ 6mm x 1.00mm
New chrome pair of grooved Bungee Nuts 6mm x 1.00mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 8mm x 1.25mm
New chrome pair of grooved Bungee Nuts 8mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Chrome Bungee Nut Set/2 ~ 10mm x 1.25mm
New chrome pair of grooved Bungee Nuts 10mm x 1.25mm. Can work as a tie down knob, spring anchor or a simple way to attach bungee cords or cargo nets.
Carb Rebuild Shop Kit - 5mm x 1,200 Bolt/Washer Assortment
1202 Piece Stainless Steel Socket Head Bolt Set with Plastic Case. All the screws you typically need when rebuilding carbs that require 5mm machine screws. This includes the carbs found on many Kawasaki KZ, Suzuki GS, Yamaha XS models with CV carbs. Includes Sizes 5X8, 5X10, 5X12, 5X14, 5X16, 5X18
Valve Lapping Stick
Valve Lapping Stick 1 1/8" & 1 3/8" Cups
Muffler Clamp
Muffler Clamp - Universal Fits 1 1/2"
Foot Pegs
Chromed Foot Pegs Pk/2 Rubber Inlay 1" & 1 1/4" Clamp Universal Fit
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Custom Ribbed Chrome Crash Bar Highway Footpeg Set
Custom Ribbed Chrome Crash Bar Highway Footpeg Set/2. 1" & 1 1/4" Clamp.
Custom Pebble Chrome Crash Bar Highway Footpeg Set
Custom Pebble Chrome Crash Bar Highway Footpeg Set/2. 1" & 1 1/4" Clamp.