Kawasaki ► KZ1000A ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki KZ1000A with universal parts included►
- Kawasaki
Rear Sprocket
Rear Sprocket (33 Tooth) Uses 530 Chain OEM Ref # 42041-1010 / 42041-169
Alternator Stator
Alternator Stator OEM Ref # 21076-023 / 21076-014
Rectiifer Regulator
Rectifier Regulator, Replaces OEM# 21066-013 / 21066-026 Mounts to the Bottom of the Battery Box (Where the Original Voltage Regulator was Mounted).
Ignition Switch and Meters Wire Harness
Ignition Switch and Meters Front Wire Harness, Replaces OEM# 25011-026
Starter Clutch Repair Kit
Starter Clutch Repair Kit
Fork Seals
Fork Seals Set/2 36 X 48 X 10.5
Fork Seal Washer Circlip Set
A set of two washers and two circlips that hold the fork seals on the 36mm forks. Replaces OEM # 44044-012 / 44043-044
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 44010-032
Wheel Seal Kit
Front Wheel Seal Kit 2 Seals 25 x 40 x 8 30 x 42 x 7.5
Wheel Seal Kit
Rear Wheel Seal Kit 2 Seals 35 x 52 x 7 40 x 62 x 7
Engine Cover Bolt Set
High Quality Premium Stainless Steel Engine Cover Bolt Set Set includes: 71 Bolts and 1 Allen key for a total of 72 pieces. These bolts are all smooth head Allen bolts and are for the alternator, clutch, points, sprocket and cam cover.
Oil Pan Bolt Set
Oil Pan Bolt Set Stainless Steel Oil Pan Bolt Set. Includes 17 Bolts and 17 Washer for 34pcs.
Bolt Set
High Quality Premium Zinc Bolt Set Set includes: 63 Bolts/Screws Replace those rusted and rounded off Phillips head case screws with this comprehensive set of correct replacement bolts for these covers - alternator, clutch, points, sprocket and carb holder bolts. The set comprises 63 correct length bolts including 6mm x 18mm & 6mm x 22mm not found in our competitors sets. The 70mm and 125mm hex head bolts are smooth head and manufactured to the correct length rather than cut down.
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Ribbed Brake Master Cylinder Dust Boot
Ribbed Brake Master Cylinder Dust Boot, Replaces OEM# 43069-001
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 43050-1004A
Rear Brake Pads
Rear Brake Pads Pk/2 OEM Ref # 43050-010 / 69130-45001 / 69130-05A00
Base Gasket
Base Gasket, Replaces OEM# 11009-030
Clutch Plate
Clutch Plate 8 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Steel Clutch Plate
Steel Clutch Plate 7 Pieces Required
Clutch Spring Kit
Clutch Spring Kit
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Intake Carb Holder Set
Intake Carb Holder Set/4 OEM Ref #16065-028 / 16065-022 / 16065-028 RH 2 Pc, 16065-029 / 16065-023 LH 2 Pc Holders include vacuum caps over the vacuum take-off spigots.
Carburetor Screw Kit
Complete Carburetor Screw Kit for 4 Carbs. Kit Includes 4X - Drain Screws with O-Rings and 28X - Screws with Lock Washers.
Float Needle & Seat
Float Needle & Seat High Quality - Made In Japan OEM Ref # 16030-027
Float Bowl Drain Screw
Float Bowl Drain Screw w O-Ring. Note: We sell these each, order the quantity you require
Gas Tank Emblem
Gas Tank Emblem with Screws, Replaces OEM# 56014-1038 The mounting holes are 122mm from center to center - Be sure to double check this will work for your motorcycle before purchase. Sold Each, Order the Quantity you Require
Throttle Cable (Push Type)
Stock Type Throttle Cable (Push Type), Replaces OEM # 54012-150
Throttle Cable ~ Pull Type
Throttle Cable ~ Pull Type - Replaces OEM# 54012-149A
Cam Chain
Cam Chain 219T x 122 D.I.D (Daido) Takes 01-8803 Rivet Link Pitch: .3061" Side Plate: Peanut Average Tensile Strength: 1800lbs OEM Ref # 94590-44122 / 21070-003 / 14401-MB6-003
Left Side Brake Hose Bracket
Left Side Brake Hose Bracket with Rubber Grommet, Replaces OEM# 43063-001 / 43064-001
Valve Shim Kit
20 Piece Valve Shim Kit with Plastic Case, 29mm Diameter Valve Shims. Includes 2 of each of the following sizes. 2.30, 2.40, 2.50, 2.55, 2.60, 2.70, 2.80, 2.90, 3.00, 3.10.
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 51059-008
Air Cleaner Inlet Rubber
Air Cleaner Inlet Rubber - For Cylinder #4 Only - Replaces OEM# 14073-1024 We Sell the 3 Other Inlet Rubbers Separately Sold Each
Air Cleaner Inlet Rubber
Air Cleaner Inlet Rubber - For Cylinder #2 or #3 Only - Replaces OEM# 14073-1023 We Sell the Other Inlet Rubbers Separately Sold Each
Air Cleaner Inlet Rubber
Air Cleaner Inlet Rubber - For Cylinder #1 Only - Replaces OEM# 14073-1022 We Sell the 3 Other Inlet Rubbers Separately Sold Each
Fork Cover Guide
Fork Cover Guide, Replaces OEM# 44064-006 / 44064-025 (Does not have the reflector mount). This is the Z1 Style - You will have to slightly modify to fit the KZ models. Sold Each
Drive Chain Adjuster
Drive Chain Adjuster with Nut and Bolt, Replaces OEM# 33040-066 If you require 2 adjusters purchase 2 of this part.
Right Side Brake Hose Bracket
Right Side Brake Hose Bracket with Rubber Grommet, Replaces OEM# 43063-001 / 43064-001
Handmade Christmas Stocking
HAPPY HOLIDAYS! We are thrilled to be able to offer handmade, one-of-a-kind upcycled Christmas stockings by “Rider Ragsâ€. Featuring a CB750 on the front. They include belt, chain and Honda keychain. Each stocking is individually handmade so there will be variations in denim and belts. Some toes face right and some left. If you have a preference for right/left toe facing make a note in the order comments.
Universal Glas-Pak Insert
Universal Glas-Pak Insert - Fits 1 1/2" Pipes - Glass Pak's Actual Size 1 3/8" Tone down your TT or Drag Pipes
Tire Valve Stem
Tire Valve Stem - Straight Metal Type
Tire Valve Stem
Tire Valve Stem - Straight Rubber Type
Tire Valve Stem
Tire Valve Stem - 90 Degree Metal Type
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/10 Metal Caps with Core Removal Notch Built In
Tire Valve Stem Caps
Tire Valve Stem Caps - Pk/2 Metal Caps with Core Removal Notch
Tire Fill Valve
Ninety Degree Tire Fill Valve
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits BF05T Cam Chains
Rivet Link
Cam Chain Rivet Link Stepped Parallel Plate Fits 219FTSS Cam Chains