Kawasaki ► KZ440D ►
-
Here’s our hand-picked list of electrical parts for your Kawasaki KZ440D with universal parts included►
- Kawasaki
Ignition Coil
Single Tower Performance High Output Ignition Coil 3.3 OHM Primary resistance ignition coil, 70 KV output. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI type) requiring a 3 OHM primary resistance coil.
Ignition Coil ~ 3 Ohm
Dual Tower Performance High Output Ignition Coil 3.3 OHM Primary resistance ignition coil, 15K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 3 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Ignition Pulser Coil
Ignition Pulser Coil 500 OHM Pulser/Trigger Fits most Yamaha & Suzuki 4 Wheelers. Consult your service manual for resistance required for your application.
Ignition Coil Tower Boots
Ignition Coil Tower Boots Pk/2 For use with our Ignition part numbers: 17-6807 & 17-6810
Coil High Tension Wire Ends (Pk/2)
Coil High Tension lead ends (fit inside coil towers) (Pk/2) Fits: #17-6810 Coil
Universal Bar Switch Assembly ~ Left (Clutch) Side
Universal Bar Switch Assembly ~ Left (Clutch) Side. Clutch side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes headlight hi-low, turn signal and horn buttons. Includes 8 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Universal Bar Switch Assembly ~ Right (Brake) Side
Universal Bar Switch Assembly ~ Right (Brake) Side. Brake side universal handlebar switch for 7/8" bars. Simple and clean design with the essentials. Includes momentary starter, kill and on/off headlight buttons. Includes 9 female bullet connectors, you may need to adapt the connectors to fit your wire harness.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.
Cylinder Wire Set
Cylinder Wire Set Black Gum Rubber - Copper Core 2 Pcs 15" Long 2 Pcs 12" Long
Spark Plug Cap
Spark Plug Cap KLG Rubber Waterproof Type Non-Resistor Universal For 14mm Plugs
Spark Plug Cap
Spark Plug Cap Short Bakelite Type For 12mm & 14mm Plugs Universal Non Resistor 90 Degree Elbow Type NGK - LZFH Style
Spark Plug Cap
Spark Plug Cap - LD05F 10mm & 12mm Thread
Spark Plug Cap
Spark Plug Cap - XD05F 10mm & 12mm Thread
Spark Plug Cap
Spark Plug Cap - XB05F 14mm Thread
LED Charging System Guage
LED Charging system indicator Gauge. Shows Voltage of your alternator rising and falling with RPM and gives a clear indication of your charging systems normal operation and early warning of problems. Gauge is Bright High Quality Chrome plated and clamps onto 7/8" Bars and can be easily wired into any point in the system (before a switched load is best). Can be mounted as shown or to handlebar by clamp (included).
Hydraulic Brake Light Switch
Hydraulic Brake Light Switch Banjo Bolt Type - 10mm x M1.25 Can Be Used Front/Rear At Single Banjo Brake Line Fitting Correct Thread For Most Honda/Kawasaki/Yamaha Stock Fittings