Kawasaki ► KZ550H ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki KZ550H with universal parts included that match “screws nuts bolts tools”►
- Kawasaki
Bearing Packer
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Flywheel Puller
Flywheel Puller 27mm x 1.0 Left Hand Thread Internal Thread Flywheels & Rotors Honda - CR80R, CR125R, CR250R, CR450R, CR500R. Many Kaw/Suz/Yam
Flywheel Puller
Flywheel Puller 20mm x 1.5 Right Hand Thread Internal Thread Flywheels & Rotors Honda - CB750 Four 69-78 SOHC Models, Suzuki - GSX-R600V, GSX-R750 T/V
Flywheel Puller
Flywheel Puller 22mm x 1.5 Right Hand Thread Internal Thread Flywheels & Rotors Honda - XL250, XL350, XL600, XR600R, XR250, XR350, XR500
Flywheel Puller
Flywheel Puller 18mm x 1.5 Right Hand Thread ( Hollow Center) Internal Thread Flywheels & Rotors Honda - 4 Cyl. Street 4-Valve Per Cylinder Engines CB750K, CB900C, CB1000 78 & Later
Flywheel Puller
Flywheel Puller 35mm x 1.5 Right Hand Thread External Thread Flywheels & Rotors
Tire Lever - 16.5" Spoon Type w Handle
Tire Lever - 16.5" Spoon Type, Forged Steel with Plastic Handle.
Brake Bleeder Hose Kit
Brake Bleeder Hose Kit. Kit includes 1-way valve, hose and clamps. This tool helps bleed motorcycle brakes quickly and easily. The 1-way valve prevents air from flowing back into the brake lines. Easy to use, simply connect and pump.
Combination Flywheel Puller Driver Set
10 Piece Combination Flywheel Puller Driver Set. Used to separate flywheel from the crankshaft taper. Supplied in a labelled plastic storage case. This 10 pieces set provides 15 different applications, sizes as follows： M14x1.5, M16x1.5, M18x1.5, M19x1.0, M20x1.0, M27x1.25, M22x1.0, M25x1.5, M22x1.5, M26x1.5, M24x1.0, M27x1.0, M26x1.0, M28x1.0, M28x1.5 Except for M27X1.0, all applications have right hand threads.
Fusil Type Tire Lever
Fusil Type Tire Lever Chrome Finish
Dunlop Type Tire Lever
Dunlop Type Tire Lever 16" Long
Digital Tire Gauge
Digital Tire Pressure Gauge Measures 1-100 PSI (0.1 - 7.0 Bar)
Wheel Bearing Remover Set
8 Piece Metric Wheel Bearing Remover Set in a Plastic Case. Includes a large and small driver with 10mm, 12mm, 15mm, 17mm, 20mm and 25mm removers. Dependable split collet design.
Tire Pressure Gauge
Tire Pressure Gauge Dial Type Measures From 10-60 PSI
6-Way Spoke Wrench
6-Way Spoke Wrench Fits #7 Thru #12 nipples
Spoke Wrench Set
Spoke Wrench Set Fits #8/9 & #10/11 Chrome
Rim Savers
Rim Savers Set/2 Protect Rim From Lever Damage
Tire Inflator
Tire Inflator 3 Function Inflator 2" Dial Guage 0-160PSI / 0-11KPA 12" Hose With Chuck
Hose Remover Pliers
Hose Remover Pliers. For easy removal of 5/32" to 1/2" hoses. The jaw digs into the tube to grip it, squeeze and the hose is easily pushed off by the jaw.
Blind Hole Bearing Puller Set
Blind Hole Bearing Puller Set Includes 2.15LB Slide Hammer With Shaft & 8 Pc Of Bearing Collets. Pulls The Following Size Bearings: 8-10mm, 10-12mm, 12-14mm, 15-17mm, 17-20mm, 20-24mm, 25-29mm, 30-32mm
382pc O-Rings Kit with Plastic Case
382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm 10X---3.53mm--21.82mm----------10X---3.53mm--34.52mm 10X---3.53mm--23.39mm----------10X---3.53mm--36.10mm 10X---3.53mm--25.00mm----------10X---3.53mm--37.70mm 10X---3.53mm--26.57mm------------7X---5.34mm--37.47mm 10X---3.53mm--28.17mm------------7X---5.34mm--40.65mm 10X---3.53mm--29.75mm------------7X---5.34mm--43.82mm
419pc O-Rings Kit with Plastic Case
419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm 10X---3.50mm--20.00mm----------10X---3.50mm--34.50mm 10X---3.50mm--22.00mm----------10X---3.50mm--36.00mm 10X---3.50mm--23.50mm----------10X---3.50mm--38.00mm 10X---3.50mm--25.00mm----------10X---3.50mm--41.00mm 10X---3.50mm--26.50mm----------10X---3.50mm--44.00mm 10X---3.50mm--28.00mm----------10X---3.50mm--47.00mm 10X---3.50mm--30.00mm----------10X---3.50mm--50.00mm
Oil / Fluid Container ~ 2 Liter
2 Liter Oil / Fluid Container with Long Spout.
Oil / Fluid Container ~ 4 Liter
4 Liter Oil / Fluid Container with Long Spout.
Reflector
Round Reflector - Amber - Black Rim 5mm thread with nut 60mm Diameter Stud Mount
Carb Float Level Gauge
Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the float height is correct to factory spec when tuning your engine. Too little or too much fuel in the float bowl will negatively affect tuning results. Adjustable to fit most carburetors. Adjustable Width: 16-78mm and Adjustable Height 0-40mm
Permatex Valve Lapping Paste
Valve Lapping Paste - Permatex Aids valve grinding and seating operations to remove burrs, surface defects, carbon and corrosion. Mixes with water to form an easy to use paste.
Adjustable Fork Seal Driver 35-45mm
Adjustable 35-45mm Fork Seal Driver. This high quality tool can be used on many different fork sizes. Use these for easy installation of most fork seals on either conventional or inverted forks.
Front Signal Lamp Stay ~ Short Type
Front Signal Lamp Stay with Nut and Washer ~ Short Type - Chrome. These are M10 x 1.50 with nut - Ensure your bike requires this thread size before purchasing. Body Length 26mm, Thread 21mm, Total Length 47mm.
Tie Down Set
Tie Down Set/2 - Red 4000lb Strength 1" Wide x 5 1/2'
Tie Down Extensions
Tie Down Extension Set/2 - Red 18"
Tie Down Set
Tie Down Set/2 - Black 4000lb Strength 1" Wide x 5 1/2'
Bar Harness
Bar Harness Eliminates Damage To Fairings, Grips & Body Covers Red Heavy Duty Nylon Web 1 3/4" x 37"
Black Tie Downs w/ Assist Carabiner
Black Heavy Duty Cam Buckle Tie Down (Set/2) w/ Assist Carabiner. Features a 3/8" diameter rubber coated hook, 1" wide straps with a length of 5.6 feet, non slip cam buckles with vinyl coating to protect chrome and paint. 1200lb Strength.
Magura Brake Master Cylinder (13mm)
Magura Front Brake Master Cylinder 13mm Piston Diameter - Recommended For Single Disk System Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Magura Brake Master Cylinder (16mm)
Magura Front Brake Master Cylinder 16mm Piston Diameter - Recommended For Dual Disk System Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Magura Clutch Master Cylinder
Magura Clutch Master Cylinder 13mm Piston Diameter Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Front Master Cylinder w Remote Reservoir - 14mm
Universal Front Brake Master Cylinder with a Remote Reservoir 14mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Adjustable Lever, Banjo Bolt Washers, Banjo Bolt.
Front Brake Master Cylinder
Universal Front Brake Master Cylinder 13mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Front Master Cylinder w Remote Reservoir - 16mm
Universal Front Brake Master Cylinder with a Remote Reservoir 16mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Adjustable Lever, Banjo Bolt Washers, Banjo Bolt.
Replacement Mirror
Replacement Mirror - Fits Right or Left - Universal Fit Universal Rounded Rectangular Tinted Type 10mm Screw In Thread Chrome Plated
Replacement Mirror
Replacement Mirror Kawasaki Z-1 Style 4 3/8" Round Mirror With Oval Back 10mm Screw Mount. 6" Long Stem
LED Turn Signal Set/2
Custom LED Turn Signal Set/2. 3.5" Long Turn Signals with 10" Long Wires, DC 12 Volt. Will screw on to 10mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
Custom LED Turn Signal Set/2
Custom LED Amber Lens Turn Signal Set/2. 2.5" Long Turn Signals with 10.5" Long Wires, DC 12 Volt. Will screw on to 8mm Screw holes. 2 Wire (Signal and Ground). These Require an LED relay to work. We sell these #12-0130
TC Bros. Universal Linkage Kit
TC Bros. Brand Universal Linkage Kit for all TC Bros. Forward Control Kits. The rods/tubes will need to be cut to fit your application. Kit includes, Two 24" Long 5/16" Threaded Rods, Four 5/16" Ball Joints, Two 5/16" ID x 1/2" OD Steel Tubes* (to cover rod threads and increase rigidity), Eight 5/16" Jam Nuts, Four Nylock Nuts and Four Flat Washers. This Set is needed for all the forward control kits we carry
Universal Fuel Petcock
Universal Fuel Petcock On/Off/Reserve Positions One straight Outlet Fitting, Two ninety degree outlet fittings & One outlet blockoff plug included. Direct fit to 3/8" NPT (Female Thread) in tank or choose adaptor plate or Nut as required.
Clutch Master Cylinder Assembly
Clutch Master Cylinder with 12.9mm Piston Diameter - Comes With: Alloy Body, Alloy Lever, Banjo Bolt Washers, Banjo Bolt and brake/clutch switch. Quality low profile design with a 10 x 1.25 Front threaded outlet.
Front Brake Master Cylinder
Universal Front Brake Master Cylinder 16mm Piston Diameter - For Dual Disk Brakes Low Profile Design With 10 x 1.25 Front Threaded Outlet Left Hand Thread Mirror Mount Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Replacement Mirror
Replacement Mirror - Fits Left & Right Side - Short Stem type Kawasaki Z-1 Style 4 3/8" Round Mirror With Oval Back 10mm Screw Mount. Short Stem