Kawasaki ► KZ650D ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki KZ650D with universal parts included that match “1”►
- Kawasaki
Turn Signal Lamp
Turn Signal Lamp - Chrome 1-Wire Front or Rear - 12 Volt
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Front Footrest Assembly
Front Passenger Footrest Assembly. Includes mounting bracket, footrests, and rubber inserts as shown. Replaces OEM # 34028-011 / 34028-012
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 11009-1866 / 18067-004 Sold Each, Order the Quantity you Require
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Brake Lever
Brake Lever OEM Ref # 43029-003 / 43029-002 / 43029-004 / 43029-1002
Kickstarter Rubber
Kickstarter Rubber OEM Ref # 13063-004 / 92161-2388
Turn Signal Lens
Turn Signal Replacement Lens - Amber - Front or Rear OEM Ref # 23048-013 / 23048-1001
Ignition Switch ~ 6 Prong Style
Ignition Switch Assembly ~ 6 Prong Style OEM Ref # 27005-083 / 27005-086 / 27005-042 / 27005-5003 / 27005-5007 / 27005-5008 Keys Included 6 Prong Connector Block - These bikes used 4 Prong OR 6 Prong Switches - check before purchasing!
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 43050-1004A
Ribbed Brake Master Cylinder Dust Boot
Ribbed Brake Master Cylinder Dust Boot, Replaces OEM# 43069-001
Ignition Switch Assembly ~ 4 Prong Style
Ignition Switch Assembly ~ 4 Prong Style OEM Ref # 27005-086 / 27005-012 Keys Included 4 Prong Connector Block - These bikes used 4 Prong OR 6 Prong Switches - check before purchasing!
Headlamp Rim
Stock Type Headlamp Rim - Chrome - Replaces OEM # 23006-038 / 23074-001
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - Replaces OEM # 23006-038 Headlight Rim / Ring, # 23072-001 Headlight Mounting / Retaining Ring and # 23074-001 Mounting Setting Ring.
Speedometer Assembly
Stock Style Speedometer Assembly, Replaces OEM # 25001-044 / 25005-121 / 25005-1031 / 25006-052 0-160MPH.
Contact Point ~ Right Side
Contact Point ~ Right Side - Replaces OEM# 21008-028
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Rear Stoplight Pedal Brake Light Switch Assembly
Rear Stoplight Pedal Brake Light Switch Assembly, Replaces OEM # 27010-1481
Contact Point ~ Left Side
Contact Point ~ Left Side - Replaces OEM# 21008-027
Fork Seals
Fork Seals Set/2 36 X 48 X 10.5
Clutch Lever
Clutch Lever OEM Ref # 46092-022 / 46092-023
Ignition Coil
Ignition Coil, 12 Volt Dual Output Point type ignition coil. Replaces OEM # 33410-45012 / 33410-45010 / 33420-45010 / 33410-44X50 / 33410-44120 / 33420-44120 / 33410-45021 / 33420-45020 / 33410-45512 / 33410-45110 / 33420-45110. Center to Center Mounting Distance: 90mm
Kawasaki Style ~ 7" Black Headlight Bucket & Rims
Kawasaki Style 7" Black Headlight Bucket with Chrome Rims. Use your own 7" light unit. Features: High quality steel construction, Kawasaki style oblong side mounting holes (not threaded). Replaces OEM #: 23005-1016 / 23006-038
Fork Dust Boots
Fork Dust Boots Set/2 OEM Ref # 44010-032
Valve Stem Seal
Valve Stem Seal OEM Ref # 92049-016
Valve Spring Retainer
Valve Spring Retainer OEM Ref # 12009-008
Primary Chain
OEM Quality Primary Chain - 52 Link OEM Ref # 13610-438-004 / 13122-007
Tachometer & Speedometer Gauge Bracket
Stock Type Tachometer & Speedometer Gauge Bracket, Replaces OEM # 25008-1005 Made from light weight black painted aluminum and with instrument gauge shock dampers. No mounting hardware included.
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Carburetor Screw Kit
Complete Carburetor Screw Kit for 4 Carbs. Kit Includes 4X - Drain Screws with O-Rings and 28X - Screws with Lock Washers.
Gas Tank Emblem
Gas Tank Emblem with Screws, Replaces OEM# 56014-1038 The mounting holes are 122mm from center to center - Be sure to double check this will work for your motorcycle before purchase. Sold Each, Order the Quantity you Require
Clutch Spring Kit
Clutch Spring Kit
Valve Tappet
Valve Tappet OEM Ref # 12032-1066
Front Brake Master Cylinder Repair Kit
Front Brake Master Cylinder Repair Kit OEM Ref # 43020-1023
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Oil Filter
Oil Filter OEM Ref # 15410-426-010 / 15410-422-004 / 16099-003 / 36Y-13441-00 Note: If you require new oil filter o-rings, springs or washers we sell these on our site as well
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 11009-1866 / 18067-004
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.