Kawasaki ► KZ750E ►
-
Here’s our hand-picked list of parts and accessories for your Kawasaki KZ750E with universal parts included that match “1”►
- Kawasaki
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Guide Roller Damper Rubber
Guide Roller Damper Rubber OEM Re f# 92075-123
Fuse Box Panel Harness ~ Small Type
Fuse Box Panel Harness, Replaces OEM # 26004-035 Full assembly includes wire connectors, box, rubber mount and fuses. Note:There are large and small Fuse Box types, this is the SMALL type.
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Exhaust Gasket (Each)
Exhaust Gasket - 1 Pc OEM Ref # 11009-1866 / 18067-004 Sold Each, Order the Quantity you Require
Gear Change Lever
Gear Change Lever Universal Fit Spline Diameter 11.5mm Total Length 6 1/2" Offset 4"
Rectifier Regulator
Rectifier Regulator 6 Wires (5 Wires in 6 Space Connector Block + 1 Red/White Wire With Male Terminal) OEM Ref # 21066-1008
Carb Rebuild Kit
Carb Rebuild Kit Includes Items Pictured High Quality - Made In Japan 1 Kit Needed Per Carb
Gas Tank Cap w keys
Stock Type Gas Tank Cap with Keys, Replaces OEM # 51048-012 Full Gas Cap Assembly with Seal, Hinge Pin and 2 Keys
Headlamp Rim
Stock Type Headlamp Rim - Chrome - Replaces OEM # 23006-038 / 23074-001
Headlamp Rim & Retainer
Headlamp Rim & Retainer Assembly - Replaces OEM # 23006-038 Headlight Rim / Ring, # 23072-001 Headlight Mounting / Retaining Ring and # 23074-001 Mounting Setting Ring.
Turn Signal Lamp
Turn Signal Lamp - Chrome 2-Wire Front or Rear
Turn Signal Lens
Turn Signal Lens - Amber - Front or Rear OEM Ref # 23048-1006 / 23048-1022
Clutch Lever
Clutch Lever OEM Ref # 46092-022 / 46092-023
Ignition Coil
Ignition Coil, 12 Volt Dual Output Point type ignition coil. Replaces OEM # 33410-45012 / 33410-45010 / 33420-45010 / 33410-44X50 / 33410-44120 / 33420-44120 / 33410-45021 / 33420-45020 / 33410-45512 / 33410-45110 / 33420-45110. Center to Center Mounting Distance: 90mm
Engine Gasket Set
Complete Engine Gasket Set Includes all Engine Gaskets High Quality - Made In Italy by Athena Athena Product #P400250850700
Valve Stem Seal
Valve Stem Seal OEM Ref # 92049-016
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Front - Dual
Brake Caliper Rebuild Kit
Brake Caliper Rebuild Kit Rear - Single
Front Brake Pads
Front Brake Pads Pk/2 OEM Ref # 43082-1007
Brake Pads
Rear Brake Pads Pk/2 OEM Ref # 43082-1008
Valve Spring Retainer
Valve Spring Retainer OEM Ref # 12009-008
Cam Chain
Silent Cam Chain 412 x 150 OEM Ref # 14401-MM5-015 / 92057-1319 / 12760-26D00 Made In Japan
Primary Chain
OEM Quality Primary Chain - 52 Link OEM Ref # 13610-438-004 / 13122-007
Tachometer & Speedometer Gauge Bracket
Stock Type Tachometer & Speedometer Gauge Bracket, Replaces OEM # 25008-1005 Made from light weight black painted aluminum and with instrument gauge shock dampers. No mounting hardware included.
Muffler Joint Gasket
Muffler Joint Gasket 35mm x 41mm x 26mm OEM Ref # 11009-1073 / 11009-1634 / 11009-1667 Fits: Headpipe
Steel Clutch Plate
Steel Clutch Plate 6 Pieces Required
Clutch Spring Kit
Clutch Spring Kit
Ignition Switch Assembly
Ignition Switch Assembly Fork Lock & Keys OEM Ref# 27005-5072 / 27005-5073 / 27005-5074 / 27005-5067 / 27005-5103 / 27005-5029 / 27005-5027 / 27005-5035 / 27005-5056 / 27005-5064 / 27005-5101 / 27005-5081 / 27005-5038 / 27005-5047 / 27005-5030 / 27005-5014 / 27005-5024
Valve Tappet
Valve Tappet OEM Ref # 12032-1066
Front Brake Master Cylinder Repair Kit
Front Brake Master Cylinder Repair Kit OEM Ref # 43020-1023
Petcock Repair Kit
Petcock Repair Kit
Progressive Type Front Fork Springs
Progressive Type Front Fork Spring Set/2. Includes 10" Pipe and Washers. These Progressive Type Springs improve handling and overall ride quality. They Stop front end droop and diving during braking while improving cornering stability. A Great Performance upgrade for your Bike! Some Bikes Require that the Spacer Length be Calculated using the instructions below then the Included Pipe Cut to make the Appropriate Sized Spacers, Some Models Do Not Require Spacers. Be Sure to Check the End of the Installation Instructions Below to see if your Bike Require Spacers.
Clutch Plate
Clutch Plate 7 Pieces Required OEM Ref # 22201-425-000 / 22201-MN5-020 / 22201-MT8-000 / 13088-030
Float Bowl Gasket
Float Bowl Gasket OEM Ref # 16019-024, 16010-323-315, 16010-323-004
Gas Cap Rubber Seal
Gas Cap Rubber Seal, Replaces OEM # 11009-1051
Float Needle
Float Needle High Quality - Made In Japan OEM Ref # 16155-382-004 / 16011-393-004 / 16011-KG0-891 / 16030-1007 / 16030-028 / 16011-382-004
Oil Filter
Oil Filter OEM Ref # 15410-426-010 / 15410-422-004 / 16099-003 / 36Y-13441-00 Note: If you require new oil filter o-rings, springs or washers we sell these on our site as well
Exhaust Gasket Pk/10
Exhaust Gasket Pk/10 OEM Ref # 11009-1866 / 18067-004
Rim Lock 1.60"
Rim Lock 1.60" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.60" rims (for most tire sizes 250-300). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Rim Lock 1.85"
Rim Lock 1.85" Rim, All Strong Rubber Type. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Mounting Clamp ~ Chrome ~ 1" Bars
Chrome Speedo/Tach/Mirror Mounting Clamp 2 Piece Die-Cast Alloy Clamp With 10mm RH Thread Fits 1" Bars
Heavy Duty Rim Lock 1.85"
Rim Lock 1.85" Rim Type, Heavy Duty Metal Base Covered with Strong Rubber. Rim Lock / Bead Lock fits to 1.85" rims (for most tire sizes 325-350). Are you popping tubes quickly? A rim lock, or "bead lock" may be exactly what you need. A rim lock secures the tire, to reduce the chance of tire slippage on the rim, ultimately protecting the inner tube. Eliminates tube pinching and casing damage!
Stud Extractor 1-6mm
Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard to reach. Use with an impact wrench. Fits studs from (1-6mm)
Black Single Cable Pull Throttle Assembly 1"
Black Single Cable Pull Throttle Assembly For 1" Bars Jackhammer Style 140mm Length Grips Features Tension Adjuster and Built in Cable Adjustment High Quality Black Powder Coated Aluminum Housing and Aluminum Throttle Tube
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Fuel Hose Quick Disconnect - 1/4" 6mm Fuel Line
Fuel Hose Quick Disconnect - For 1/4" or 6mm fuel line. Fuel line cut off for a quick and easy way to cut off fuel supply while working on your bike.
Universal 1 Ohm Dual Output 6V Ignition Coil
Universal 1 Ohm Dual Output 6V Ignition Coil. Will work on a number of Honda, Kawasaki, Suzuki, Yamaha, Norton, BSA, Triumph and other motorcycles with 6 volt dual output ignition coils. Check the coil mount spacing on your bike before you order. Mounting holes are 90mm (3.5") apart center to center. Low tension wires 390mm (15") long. Female spade connectors at the coil and male and female bullet connectors at the other ends. Spark plug wires (high tension leads) 570mm (24") long with 300mm (12") protective sheath.