Kawasaki ► VN400C ►
-
Here’s our hand-picked list of universal parts and accessories►
- Kawasaki
Fork Cap Wrench ~ 35MM Size
Fork Cap Wrench ~ 35MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 35MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~32MM Size
Fork Cap Wrench ~ 32MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 32MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~30MM Size
Fork Cap Wrench ~ 30MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 30MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fork Cap Wrench ~24MM Size
Fork Cap Wrench ~ 24MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 24MM fork caps. This wrench will allow you to remove your fork caps without worrying about damaging them.
Fluid Hose Clamp
Fluid Hose Clamp, all steel construction with adjustable locking collar. Completely or partially closes flexible brake, fuel, and vacuum fluid lines.
Portable Auxiliary Fuel Tank Tool
Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet and outlet. Fuel capacity 2 Litres. For use when tuning a motorcycle with the gas tank removed. Note: This tool is not to be used for long term fuel storage, for safety and to prevent accidental spillage, immediately drain gas back to approved long term storage container after use.
Rotor and Sprocket Holder
Rotor and Sprocket Holder. Keeps rotors, flywheels and sprockets from rotating during removal and installation. The adjustable stop-screw keeps the tool open at a set distance. Holds sprockets and rotors with holes center to center at a minimum distance of 13mm and a maximum distance of 230mm's.
Bearing Packer
Wheel Bearing Grease Packer. To pack a bearing, place the bearing on the piston, press down on the cap until the old grease is forced out and the new grease shows on top of the bearing. Grease stays in the tool cavity, not on your hands. Transparent, impact resistant cup allows easy grease level checks. Works on bearings up to 3-1/2" OD or 89mm.
Steering Race Remover 25-35mm
Steering Head Bearing Race Remover, Range 25-35mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 25mm to 35mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Steering Race Remover 35-55mm
Steering Head Bearing Race Remover, Range 35-55mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from 35mm to 55mm inside diameter. Can be driven with any hammer or mallet. Slips in the headtube solid end first until it snaps in behind the bearing race, then simply drive the race out of the frame.
Carb Cleaning Tool Set
Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor passages and jets.
Aluminum Timing Degree Wheel
Aluminum Timing Degree Wheel 7" Diameter with Large Visible Markings. This Tool Allows for Extremely Accurate Marking which Makes Getting the Timing Right the First Time a Breeze! Lightweight and Durable Tool. This Tool Can be used for Crankshaft Positioning, Ignition and Camshaft Timing.
Swing Arm / Rising Rate Linkage Bearing Install Tool
Swing Arm / Rising Rate Linkage Bearing Install Tool Designed for installation of the swingarm bearings on late-model Japanese off-road motorcycles. Puller draws bearing into the swingarm. Includes three drivers for use with common bearing sizes Kit includes driver sizes: I.D. 20mm / O.D 26mm, I.D. 21mm / O.D. 26mm & I.D. 22mm / O.D.26.8mm
Handlebar Top Clamp
Handlebar Top Clamp Chrome Custom Handlebar Top Clamp with Plated Allen Socket bolts. Mounting Holes center to center length 100mm, center to center height 35mm.
Carburetor Synchronizer Vacuum Gauge ~ 2 Carb Synchronizer
Carburetor and throttle body synchronizer kit for bikes with 2 Carbs. Makes synching your carburetor setup fast and easy! For use with Honda, Kawasaki, and Suzuki models (which typically have 5mm connections) that use sets of 2 carbs. Includes 2 easy to read gauges, Mountable bracket, 180mm extensions - 5mm threads, 65mm extensions - 5mm threads,Necessary hoses, Dampening valves (included to help control needle jump) and instructions.
Socket Head Cap Screw Pk/10
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 15mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 20mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 25mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 30mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 35mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 40mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 6 x 55mm
Chrome ~ Phillips Head Screw (Pk/2)
Phillips Head Screw Pk/2 Chrome Plated Size: 6 x 28mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 16mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 18mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 20mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 25mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 30mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 35mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 40mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 45mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 50mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 55mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 65mm
Socket Head Cap Screw
Socket Head Cap Screw Pk/10 Zinc Finish Size: 5 x 16mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 90mm
Phillips Head Screw
Phillips Head Screw Pk/10 Steel Plated Size: 6 x 100mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 10mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 16mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 20mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 25mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 30mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 35mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 40mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 45mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 50mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.0 Pitch Size: 6 x 60mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.25 Pitch Size: 8 x 12mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.25 Pitch Size: 8 x 16mm
Hex Head Bolt
Hex Head Bolt Pk/10 Plated - 1.25 Pitch Size: 8 x 20mm