Suzuki ►
-
Pick your Suzuki motorcycle from the list below►
- Suzuki
Mid Body Rebuild Kit w Screws
Keihin FCR Mid Body Rebuild Kit with Screws.
Drain Plug Crush Washer
Drain Plug Crush Washer 12mm x 18mm x 1mm
Oil Drain Plug
Magnetic Oil Drain Plug 14mm Diameter 1.25 Thread Pitch OEM Ref # 09247-14001
Oil Drain Plug
Magnetic Oil Drain Plug 12mm Diameter 1.50 Thread Pitch OEM Ref # 92800-12000 / 92066-1174 / 01107-12208
Haynes Workshop Manual
Haynes Workshop Manual Suzuki GS1000 Fours 1977-1979 997cc
Master Cylinder Reservoir Kit
Master Cylinder Reservoir Kit - Front 4 Screw Cover
Flywheel Puller
Flywheel Puller M24mm x 1.5mm RH Internal Thread
Velocity Stack Set
Velocity Stack Set. These Velocity Stacks are a High Quality, 39mm ID, Taper Tipped Build. Set Comes Complete with 4 Velocity Stacks with Debris Screens, Set Screws and Set Screw Allen Wrench. These install easily and look amazing once installed!
Clutch Slave Cylinder Repair Kit
Clutch Slave Cylinder Repair Kit OEM Ref # 09285-06015 Oil Seal 23164-05A00 Spring 23163-05A00 Piston Cup 59122-01A00 Bleeder Bolt Cap
Clutch Slave Cylinder Repair Kit
Clutch Slave Cylinder Repair Kit OEM Ref # 09285-06015 Oil Seal 23164-05A00 Spring 23163-06B00 Piston Cup 59122-01A00 Bleeder Bolt Cap
Ignition Switch Assembly
Ignition Switch Assembly Fork Lock & Keys For Models With Square Steering Lock Bolt OEM Ref # 37100-45301 / 37100-47011 / 37100-49201 / 37100-48B10
Ignition Switch Assembly
Ignition Switch Assembly Fork Lock & Keys Connector Block - 4 Flat Female Terminals For Models With Square Steering Lock Bolt OEM Ref # 37100-17C00 / 33600-01D02 / 33600-01D20 / 37100-26D02 / 37100-33E01 / 37100-06B00 / 37100-47011
Carburetor Adjusting Tool
Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo design allows unlocking of the locknut, adjustments to the balancing screw and re-locking the lock nut in one step.
Screw Extractor Set
Screw Extractor Set 5 Pc Set 1/8", 3/16", 15/64", 5/16", 3/8" Used to remove broken off studs, bolts & screws.
Safety Wire Nut & Metric Bolt Drill Jig Kit
Safety Wire Nut & Metric Bolt Drill Jig Kit. Contains one nut drill jig and one metric bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts.
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit
Safety Wire Nut & Metric+Imperial Bolt Drill Jig Kit. Contains one nut drill jig, one metric bolt jig and one imperial bolt jig. Jig set designed for accurate drilling of nuts and bolts for use with safety lock wire. Both jigs can be mounted in a vice for drilling. The nut drill jig allows the safety wire holes to be drilled through the head of bolts or through nuts, across the diagonal easily. Accepts up to a 3.5mm diameter. Metric bolt drill jig provides 6 drill holes for metric sizes 6 X 1.0, 8 X 1.0, 8 X 1.25, 10 X 1.25, 10 X 1.5 and 12 X 1.5 bolts. Imperial bolt drill jig provides 6 drill holes for imperial sizes 1/4"-20, 5/16"-18, 5/16"-24, 3/8"-16, 3/8"-24 and 7/16"-14 bolts.
Brake Nut Adjust Tool
Brake Nut Adjust Tool, 14mm Size.
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 4 Piece Set For both 9mm & 10mm valve adjuster screw locknuts. Screwdriver tip & 4mm square tip for valve adjuster screws. For Honda/Yamaha/Suzuki
Fork Cap Socket Tool
19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many Bikes
Tappet Adjusting Tool Set
Tappet Adjusting Tool Set 6 Piece Set Includes T-Socket Wrenches - 8mm, 9mm, 10mm Sizes 3 Adjusters - Slotted Screw, 3mm Square, 4mm Square
Gold Bullet Shaped License Plate Bolt
Gold Colored Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
Chrome Bullet Shaped License Plate Bolt
Chrome Bullet Shaped Bolt with Nut and Washer. These bullet shaped bolts are made from cast aluminum. The Bullet is 3/4" tall with a 3/4" round base. The 3/4" long x 1/4"-20 threaded stud is removable. There are many uses for these bolts including license plate holder bolts and more! They can be mounted to about anything using 1/4"-20 bolts or screws to hold the bullets in place. Note: Sold Each, Order the Quantity you Require
Extractor & Drill Set
10 Piece Extractor & Drill Set in a Plastic Case. Set contains 5X extractors (#1 through #5) and 5X mechanic's length cobalt drills. Removes bolts and screws up to 5/8". Cobalt Drill and Screw Extractor Sizes: 5/64", 7/64", 5/32", 1/4", 19/64"
6" Hanger strap - 2 hole with nut & bolt - Chrome
6" Chrome Hanger strap with nut & bolt.
JIS Screw Bit Set
JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand up to the rigors of heavy duty impact driving) PH1, PH2, PH3. Most screws used on Japanese motorcycles are NOT phillips but JIS type (Japanese Industry Standard). JIS screws look like a phillips end but have a tiny dot stamped onto the face. It is important to use these correct JIS type bits when working on your motorcycle as phillips bits ARE different and using them are more likely to result in stripping/slipping screws. Get this correct set of JIS bits for your motorcycle today!