Suzuki ► RV200L7 ►
-
Here’s our hand-picked list of electrical parts for your Suzuki RV200L7 with universal parts included►
- Suzuki
Custom Micro Push Button/Kill Switch
Custom Micro Push Button/Kill Switch. High quality chrome switch designed to clean up the appearance of your bike while allowing the use of a switch. Works great as a hidden start/kill or horn button. Includes a contoured washer which allows for installations on round surfaces such as handlebars or frames. Switch Size 14mm x 12mm with 2X 20" wires.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"
Headlight Bracket Set (34mm)
Aluminum Custom Headlight Brackets 34mm Headlight Mounting Holes 7/16"
Headlight Bracket Set
Headlight Bracket Set - Black 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Custom Universal Headlamp
Custom Universal Headlamp 4 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Custom Universal Headlamp
Custom Universal Headlamp 5 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Rectangular Headlamp
Small Rectangular Headlamp 6.5"x4.5" Lens Steel Lens Frame, With Black Plastic Housing Halogen Bulb & Headlamp Plug With Wires Side Mount, 14mm Mounting Holes, 7.25" Width Two Openings On Back
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
Headlight Assembly
Chrome 7" Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. H4 Bulb with European style parking light (Not used for North American models)
Classic Round Black Taillight
Classic Round Black Taillight with plate bracket. 2 1/4" Round lens (with a clear bottom to light up your plates), 12 Volt double filament bulb. Works as a running and brake light.
Mini Bates Style LED Taillight ~ Chrome
Mini Bates Style LED Taillight ~ Chrome. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Mini Bates Style LED Taillight ~ Black
Mini Bates Style LED Taillight ~ Black. 12 Volt taillight with 8 super bright LED's. Has running and brake light functions. Comes with mounting hardware and swivel bracket which allows it to be angled at different positions. Lens is 1 3/4" round, Outer bezel is 2 1/4" in diameter and is 2 1/4" long, Stands about 3" tall from base of mounting bracket. 3 Wire lead is about 12" long with bullet connectors. (Ground, running and brake light Wiring instructions) RED = Stop YELLOW = Running Lights BLACK = Ground
Beehive Chrome Taillight
Beehive Chrome Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4″ Length, 3″ Width, 4″ Height.
Beehive Black Taillight
Beehive Black Taillight Universal fender mounting for most applications. For under plate mounting, with upward plate illumination. 12 volt bulb, Gasket for fender mounting and plate bracket included. 6 3/4" Length, 3" Width, 4" Height.
Vintage Round Black Taillight
Vintage All Steel Round Satin Black Taillight with plate bracket. 1 5/8" Round lens (with a clear bottom to light up your plates), 12 volt double filament bulb. Works as a running and brake light. Base mounting plate measures 2" top to bottom and 2 1/2" wide. Mounting base 6mm holes are 1 1/4" wide x 7/8" top to bottom, tag mounting plate measures 6 1/2" wide, tag mounting holes 4 1/2" centered.
Black Sparto Tailight
Tail Light Assembly - Black Sparto Classic 50's design. Dual filament Bulb. Not DOT approved for Highway use.
Headlight Shell and Rim
Custom 7" Satin Black Side Mount Headlight Shell with Chrome Trim Ring. Designed for 7" sealed type headlights. Includes a 3 wire plug that works with sealed beam or H4 bulbs as well as the clip/screw and wire clips. Side mounting holes are threaded to use 5/16-24 bolts (bolts not included). Outer side mounting points are 7" apart. 3" Mounting depth from mounting holes to the back of the bucket. Sealed beam Headlight sold separately #09-0008 (Below), or the upgraded halogen beam #09-0051
LED Taillight
Custom LED Taillight. Small and lightweight, this cool little LED taillight includes a swiveling mounting bracket with about 100 degrees of up or down adjustment making it ideal for many custom applications. Featuring a clear lens with 8 super bright red LED's for the taillight and brake light as well as 5 clear LED's for the license plate illumination. Machined from aluminum in anodized black. Not DOT approved. Dimensions are approximately 1-7/8" wide x 1-3/4" deep.
Black Tail Lamp Assy. - Custom British Style
Black Tail Lamp Assy. - Custom British Style with alloy mount bracket and license plate illumination. These are perfect for many cafe and custom projects. Includes everything shown. Lens Dimensions: 4-1/2" Wide, 2-1/8" High, 1-3/4" Depth Full Assembly Dimensions: 7" Total Width, 5-1/2" Total Length, 3-1/2" Total Height
Custom Chrome Dual Beam Headlights
Custom Chrome 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
Custom Matte Black Dual Beam Headlights
Custom Matte Black 4" Dual Beam Headlight Set. Complete universal side mount dual hi/low beam head light assembly. The two high quality glass sealed beam style lights have H4 60/55 watt bulbs along with pilot running lights in each light. Assembled and pre-wired harness to simply plug into your existing H4 plug. Side mounting bolts hole are threaded for M8 x 1.25 bolts. Total outer width at side mounting bolts in 8 1/2" wide. Center of mounting bolts to rear of the light bucket is 2 5/8" in depth. From the front of the trim ring to the rear of the bucket is about 4 1/2" in depth.
Custom Bates Style 5 3/4" Black Bottom Mount Headlight
Custom Bates Style 5 3/4" Satin Black Bottom Mount Headlight. Glass sealed beam, 12 Volt 60/55 watt dual filament H4 bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing. Comes with a 3 wired plug that works with H4 bulbs. Assembled ready to mount, hook up the 3 wires and ride!
Black Projected Sparto Tailight
Black Sparto Taillight with a Projected 1 7/8" Lens. Made from Aluminum with 12" 2 wire leads self grounding for easy hook up. 5 3/4" long, 4 7/8" wide and 3 1/4" tall. Includes dual filament bulb 12V 23/8W and mounting hardware.
Custom Mini Deco Turn Signal Lamp Set
Custom Mini Deco Turn Signal Lamp Set/2. High quality die cast body with interchangeable lenses (amber and red). Can be wired as turn signals or running lights. Stem base to outer edge of body 2 1/2", body is 1 7/8" x 2 7/8" long, mounting stud 1/4" diameter x 3/4" long
Turn Signal Light Mount Bracket Holder Set
Black Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
Turn Signal Light Mount Bracket Holder Set
Chrome Metal Fork Ear Clamp/Turn Signal Light Mount Bracket Holder Set/2 with Screws, Washers and Nuts. Fits 30-45mm Front Forks
Vintage Round Chrome Taillight
Vintage All Steel Round Chrome Taillight with plate bracket, bolts and washers. 1 5/8" Round plastic lens (with a clear bottom to light up your plates), 12 volt double filament bulb. Works as a running and brake light. Base mounting plate measures 2" top to bottom and 2 1/2" wide. Mounting base 6mm holes are 1 1/4" wide x 7/8" top to bottom, tag mounting plate measures 6 1/2" wide, tag mounting holes 4 1/2" centered.
Chrome Sparto Tailight
Tail Light Assembly - Chrome Sparto Design. Dual filament Bulb. Not DOT approved for Highway use.
1156 White LED Turn Signal Bulb Set/2
1156 White LED Turn Signal Bulb Set/2 These high brightness LED bulbs look amazing! Can be used for turn signals. Bulb total length 42mm, width 15mm. These are super bright 1600 Lumen LED bulbs. Well built with Aviation-grade aluminum. Made-to-last design is vibration resistant - great for withstanding rough rides. Upgrade your bike today! Some motorcycles require the buzzer to be disconnected in order to use LED's. When switching to LED Signals you must change your flasher relay to an LED compatible relay - We carry these #12-0130.
1156 Amber LED Turn Signal Bulb Set/2
1156 Amber LED Turn Signal Bulb Set/2 These high brightness LED bulbs look amazing! Can be used for turn signals. Bulb total length 42mm, width 15mm. These are super bright 1600 Lumen LED bulbs. Well built with Aviation-grade aluminum. Made-to-last design is vibration resistant - great for withstanding rough rides. Upgrade your bike today! Some motorcycles require the buzzer to be disconnected in order to use LED's. When switching to LED Signals you must change your flasher relay to an LED compatible relay - We carry these #12-0130.
1157 White LED Turn Signal or Tail Light Bulb Set/2
1157 White LED Turn Signal or Tail Light Bulb Set/2 These high brightness LED bulbs look amazing! Can be used for turn signals or the tail light. Bulb total length 42mm, width 15mm. These are super bright 1600 Lumen LED bulbs. Well built with Aviation-grade aluminum. Made-to-last design is vibration resistant - great for withstanding rough rides. Upgrade your bike today! Some motorcycles require the buzzer to be disconnected in order to use LED's. When switching to LED Signals you must change your flasher relay to an LED compatible relay - We carry these #12-0130.
1157 Amber LED Turn Signal Bulb Set/2
1157 Amber LED Turn Signal Bulb Set/2 These high brightness LED bulbs look amazing! Can be used for turn signals. Bulb total length 42mm, width 15mm. These are super bright 1600 Lumen LED bulbs. Well built with Aviation-grade aluminum. Made-to-last design is vibration resistant - great for withstanding rough rides. Upgrade your bike today! Some motorcycles require the buzzer to be disconnected in order to use LED's. When switching to LED Signals you must change your flasher relay to an LED compatible relay - We carry these #12-0130.
Turn Signal Bulb ~ Single Filament ~ 6V / 18W ~ 1129 Bulb - Pk/2
Turn Signal Bulb ~ Single Filament ~ 6V / 18W ~ 1129 Bulb - Pk/2 BA15S Base
Turn Signal Bulb ~ Single Filament ~ 12V / 23W ~ 1073 Bulb - Pk/2
Turn Signal Bulb ~ Single Filament ~ 12V / 23W ~ 1073 Bulb - Pk/2 BA15S Base
Tail Light Bulb ~ Dual Filament ~ 6V / 23W ~ 1154 Bulb - Pk/2
Tail Light Bulb ~ Dual Filament ~ 6V / 23W ~ 1154 Bulb - Pk/2 BAY15D Base
Tail Light Bulb / Running Light ~ Dual Filament ~ 12V / 23W ~ 1157 Bulb - Pk/2
Tail Light Bulb / Turn Signal Running Light ~ Dual Filament ~ 12V / 23W ~ 1157 Bulb - Pk/2 BAY15D Base