Yamaha - ATV ► YFM80GH ►
-
Here’s our hand-picked list of parts and accessories for your Yamaha - ATV YFM80GH with universal parts included►
- Yamaha - ATV
90mm Exhaust Spring Set
90mm Exhaust Spring Set/2. Used for spring attached mufflers and exhaust pipes. Great for customizing your cafe racer, bobber, tracker or chopper. Works on any style motorcycle.
Ignition Coil ~ 5 Ohm
Dual Tower Performance High Output Ignition Coil 5.2 OHM Primary resistance ignition coil, 17K OHM Secondary Resistance. Can be used with all contact point ignitions and aftermarket electronic ignitions (non CDI) requiring a 5 OHM Coil. Fits most CB's, KZ/Z1 900/1000, KZ650 etc
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2 With Plug Wires
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2 with Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. Wires are 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Charge Monitor
Dynatek Charge Monitor. Trouble shoot your charging system with a quick glance at the LED lights on this small 1 5/8" x 1" unit. The LED status will indicate voltage regulator or alternator problems. The Dyna Charge Monitor is a valuable addition to vehicles with a battery ignition and a charge system as found on nearly all stock vehicles. The Charge Monitor allows easy determination of the operational state of the charging system with a quick glance at the indicator LED's. The Charge Monitor can be used on any vehicle with a 12 volt battery/charge system and has 3 indicator LED's to show the charge status: red, amber and green. When the right most red LED is on the battery is being overcharged due to a faulty voltage regulator. When the green LED is on, the battery is being charged at a normal voltage. When the left most red LED is on, the battery voltage is getting very low and the charge circuit or battery is failing. High quality made in the USA. Comes with a one year warranty through the manufacturer.
Performance Tool Spark Plug Crimper Tool
Performance Tool Spark Plug Crimp Tool. Perfect crimping tool for any spark plug wires. Incorporates wire cutter, terminal crimper tool and stripper in one handy tool. Black anodized finish with insulated hand grips. Crimp slot on the end of the tool secures most ignition terminals including "W" type, right angle and "High Tower" terminals. Crimps 7mm to 8.5mm ignition wire. Works with 10 to 22 gauge solderless terminals. High quality made in the USA. Comes with a lifetime warranty through the manufacturer!
Dynatek Performance Spark Plug Wire Set
Dynatek Performance Spark Plug Wire Set, 7mm Black Silicone Copper Core. 4' Length (cut to your needed length). 2 wires in this set which can be cut into 4. All wires are supplied with finished spark plug boot ends and loose coil terminals to allow the final length to be determined by the user. Wires feature a solid copper core for use on older vehicles where electrical interference is not an issue. High quality made in the USA. Will work with Dyna Style Coils only # 07-9979, 07-9980 or 17-6810.
Dynatek Performance High Output 5 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 5 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Dynatek Performance High Output 3 Ohm Ignition Coil Set/2
Dynatek Performance Dual Output 3 Ohm Ignition Coil Set/2. Includes Hardware and Instructions. Comes with a one year warranty through Dynatek. These high tech, top quality coils are made in the USA and are designed for maximum performance. They produce spark voltages in excess of 30,000 volts and spark energies second to none. Dyna Coils work with point ignitions, aftermarket electronic ignitions and factory electronic ignitions. Before selecting a coil check the coil primary resistance requirements as specified by the manufacturer of the ignition being used before purchasing. When choosing the right coil for your bike, never select a coil with a lower resistance than your ignition system.
Brake & Clutch Lever Assemblies
Brake & Clutch Lever Assemblies. Includes both the clutch and brake levers and both perches (brackets). These are universal for 7/8" bars with cable operated drum brakes, and are great for custom projects. Levers do not include mirror attachments points.
Brake Lever
Power Brake Lever - Universal Short Alloy Lever Assembly. Suitable for Yamaha/Suzuki/Kawasaki
Clutch Lever
Power Clutch Lever - Universal Short Allow Lever Assembly Suitable For Yamaha/Suzuki/Kawasaki
Cable Adjuster
Cable Adjuster - Universal For 8mm & Smaller Cables Threaded 18mm
Cable Adjuster
Cable Adjuster - Universal For 9mm Cables Threaded 17mm
Cable Adjuster
Cable Adjuster - Universal For 8mm & Smaller Cables Threaded 23mm
Magura Brake Master Cylinder (13mm)
Magura Front Brake Master Cylinder 13mm Piston Diameter - Recommended For Single Disk System Stroke 12mm, Thread for Brake Light Switch Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
Magura Brake Master Cylinder (16mm)
Magura Front Brake Master Cylinder 16mm Piston Diameter - Recommended For Dual Disk System Thread for Brake Light Switch Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
Magura Clutch Master Cylinder
Magura Clutch Master Cylinder 16mm Piston Diameter Stroke 12mm Brake Switch (12-0002), Banjo Bolt (08-0254) and Banjo Bolt Washer (08-0258) Sold Separately.
Banjo Bolt
Banjo Bolt M10 x 1.0 x 21mm Fits: Magura, some Suzuki & most European Master Cylinders.
Universal Front Brake Master Cylinder
Universal Front Brake Master Cylinder (13mm) Alloy body master cylinder assembly. Includes lever, banjo bolt, banjo washers and brake switch. Quality low profile design with 10 x 1.25 front threaded outlet. Left hand thread mirror mount. Recommended for Single disk systems.
Banjo Bolt
Banjo Bolt M10 x 1.25 x 21mm Fits: Most Honda, Yamaha & Kawasaki masters with single brake hose.
Banjo Bolt Washers Pk/10
Banjo Bolt Washers Pk/10 For 10mm Banjo Bolts
Brake Bleed Screw
Brake Bleed Screw M7 x 1.0 x 27
Front Master Cylinder w Remote Reservoir - 14mm
Universal Front Brake Master Cylinder with a Remote Reservoir 14mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Adjustable Lever, Banjo Bolt Washers, Banjo Bolt.
Clutch Master Cylinder Assembly
Clutch Master Cylinder with 12.9mm Piston Diameter - Comes With: Alloy Body, Alloy Lever, Banjo Bolt Washers, Banjo Bolt and brake/clutch switch. Quality low profile design with a 10 x 1.25 Front threaded outlet.
Front Brake Master Cylinder
Universal Front Brake Master Cylinder 13mm Piston Diameter Low Profile Design With 10 x 1.25 Threaded Outlet Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Rear Brake Master Cylinder 13mm Piston
Universal/Custom Rear Brake Master Cylinder for Custom or Race Use 13mm Bore - Alloy body with remote fluid reservoir & hose. M10 x 1.25 threaded outlet, adjustable clevis. Has 2X 8mm threaded mounting holes at 49mm center to center. Check that this 49mm size will work to mount on your bike before purchasing. Includes 10mm x 1.25 outlet banjo bolt.
Front Brake Master Cylinder
Universal Front Brake Master Cylinder 16mm Piston Diameter - For Dual Disk Brakes Low Profile Design With 10 x 1.25 Front Threaded Outlet Left Hand Thread Mirror Mount Comes With: Alloy Body, Alloy Lever, Brake Switch, Banjo Bolt Washers, Banjo Bolt.
Standard Double Banjo Bolt ~ M10 X 1.0
M10 X 1.0 (Fine Thread) Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
Standard Double Banjo Bolt ~ M10 X 1.25
M10 X 1.25 - Standard Double Banjo Bolt with Washers ~ used when stacking 2 lines. 32mm length to bottom of bolts head. High Quality Stainless Steel
12mm Master Cylinder Sight Glass
12mm Master Cylinder Sight Glass with O-Ring.
14mm Master Cylinder Sight Glass
14mm Master Cylinder Sight Glass with O-Ring
18mm Master Cylinder Sight Glass
18mm Master Cylinder Sight Glass with O-Ring
Chrome Goldwing Emblem Set/2
Chrome 3D Goldwing Emblem Set/2. Features a Sticker Back for Easy Application. These Custom Emblems Can Be Used Anywhere! 16.5cm Long x 1cm Width x 0.40cm Thickness
Gold Goldwing Emblem Set/2
Gold 3D Goldwing Emblem/Decal Set/2. Features a Sticker Back for Easy Application. These Custom Emblems Can Be Used Anywhere! 16.5cm Long x 1cm Width x 0.40cm Thickness
Black Universal Adjustable Headlight Brackets
Universal Adjustable Headlight Bracket Set/2 - Black Finish. Fits: 35-41mm Forks
Headlamp Visor (7")
Headlamp Visor With Eagle Emblem Fits 7" Headlight
Tommaselli Type Headlight Brackets (35mm-36mm)
Tommaselli Type Headlight Brackets 35-36mm
Headlight Bracket Set
Headlight Bracket Set - Chrome 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Tommaselli Type Headlight Brackets (32mm-34mm)
Tommaselli Type Headlight Brackets 32-34mm
Headlight Bracket Set (35mm)
Aluminum Custom Headlight Brackets 35mm Headlight Mounting Holes 7/16"
Headlight Bracket Set (34mm)
Aluminum Custom Headlight Brackets 34mm Headlight Mounting Holes 7/16"
Headlight Bracket Set
Headlight Bracket Set - Black 3-Hole Type Universal Adjustable Fit - 32mm-38mm
Cast Aluminum Black Headlight Bracket Set
Cast Aluminum Black Headlamp Mounting Bracket Set. Sold with adapters to fit 35mm, 39mm and 41mm fork tube outer diameters.
Custom Universal Headlamp
Custom Universal Headlamp 4 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Custom Universal Headlamp
Custom Universal Headlamp 5 1/2" Chrome bottom mount lamp assembly. High beam indicator. Halogen bulb and headlamp plug with wires.
Rectangular Headlamp
Small Rectangular Headlamp 6.5"x4.5" Lens Steel Lens Frame, With Black Plastic Housing Halogen Bulb & Headlamp Plug With Wires Side Mount, 14mm Mounting Holes, 7.25" Width Two Openings On Back
Custom Bates Style 4 1/2" Black Bottom Mount Headlight
Custom Bates Style 4 1/2" Satin Black Bottom Mount Headlight. Glass sealed beam with a P15D base, 12 volt 35/35 watt bulb, 16" wire leads. Blue dot high/low beam indicator on top of light housing.
Headlight Shell & Rim
Custom Ready to Assemble Chrome Side Mount Headlight Bucket Rim & Retainer. Designed for 7" sealed or non sealed H4 type headlights. Chrome all metal bucket with chrome trim ring. Side mounting holes are threaded (13.5mm). Outer side mounting points are 7-1/2" apart. Comes with a wired plug that works with sealed beam or H4 bulbs. H4 Beam Headlight sold separately #09-0072
Headlight Assembly
Chrome 7" Side Mount Headlight Assembly. Chrome all metal bucket with chrome trim ring. H4 Bulb with European style parking light (Not used for North American models)
Classic Round Black Taillight
Classic Round Black Taillight with plate bracket. 2 1/4" Round lens (with a clear bottom to light up your plates), 12 Volt double filament bulb. Works as a running and brake light.