Tools

Carb Cleaning Tool Set (35-9125)

$12.64

Carburetor Cleaning Tool Set. Includes 12 steel wire ends and a small file designed for cleaning nozzles and the tiny holes found in carburetor...

JIS Screw Bit Set (35-0047)

$15.30

JIS Type 6 Pc. Screw Bit Set with Caribiner Holder. Includes 25mm Bits - PH1, PH2, PH3 and 25mm Torsion Bits (designed to stand...

382pc O-Rings Kit with Plastic Case (35-0066)

$25.20

382pc O-Rings Kit with Plastic Case. 30 different sizes included in mm's. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.78mm--2.90mm------------13X---2.62mm--9.19mm 20X---1.78mm--3.69mm------------13X---2.62mm--10.77mm 20X---1.78mm--4.47mm------------13X---2.62mm--12.37mm 20X---1.78mm--5.29mm------------13X---2.62mm--13.95mm 20X---1.78mm--6.07mm------------13X---2.62mm--15.54mm 20X---1.78mm--7.65mm------------13X---2.62mm--17.12mm 20X---1.78mm--9.25mm------------13X---2.62mm--18.72mm 10X---3.53mm--18.64mm----------10X---3.53mm--31.34mm 10X---3.53mm--20.22mm----------10X---3.53mm--32.92mm...

Clutch Center Nut Removal Tool (35-0051)

$12.64

Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Inside diameter 24mm, use with 3/8" driver.Part...

Portable Auxiliary Fuel Tool (35-9120)

$49.14

Portable Auxiliary Fuel Tank, for Non Fuel Injection Systems. Includes 4 Feet of 1/4" fuel line and an inline fuel valve with 1/4" inlet...

Spark Plug Gapping Tool (35-0136)

$3.86

Circular Spark plug gap tool. Marked in thousandths of an inch and millimeters.Part Number: 35-0136

Master Cylinder Snap Ring Plier (35-0009)

$19.29

Master Cylinder Snap Ring Plier Deep Right Angled Snap Ring Pliers To Remove Recessed CirclipsPart Number: 35-0009

Sold out

Carb Cleaning Tool Set (35-9110)

$10.77

Carburetor Cleaning Tool Set. Includes 20 steel wire ends designed for cleaning the tiny holes found in carburetor jets. Cleaning wire sizes range from...

Seal Puller (35-8000)

$14.70

Seal Puller for Large Size Seals.Part Number: 35-8000

Carburetor Synchronizer Vacuum Gauge ~ 2,3,4 Cylinders (35-0085)

$97.09

Carburetor and throttle body synchronizer kit for bikes with 2, 3 or 4 Cylinders. Makes synching your carburetor setup fast and easy! For use...

Carb Float Level Gauge (35-0043)

$19.88

Carburetor Float Level Gauge. Used to measure the float height between the float and carburetor gasket surface. It is important to make sure the...

Rear Wheel Bearing Removal Tool (35-9129)

$18.55

Rear Wheel Bearing Removal Tool, Removes OEM#'s 41231-286-000 / 41231-429-000 Features a 22mm hex and 3/8" square drive. Prevents damage to the retainer ring.Part...

Vintage Motorcycle Tool Set (73-0078)

$30.59

Vintage Motorcycle Tool Set. Have you lost the original tool set that came with your motorcycle? Well, we have a great alternative for you!...

Fork Cap Wrench ~32MM Size (35-9114)

$5.85

Fork Cap Wrench ~ 32MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 32MM fork caps. This wrench will...

Piston Ring Tool (35-9112)

$21.95

Piston Ring Tool with plastic storage case. This tool is designed to prevent ring breakage during cylinder installation. This tool can be easily removed...

Deep Allen Socket Driver Set (35-9049)

$32.92

Deep Allen Socket Driver Set 8 Pc Set - 140mm Bits Includes 1/2" Drive, Socket Sizes - 5, 6, 7, 8, 10, 12, 14...

Feeler Gauge Set (35-1768)

$9.64

Feeler Gauge Set - Metric Feeler Gauge Set for setting valve and contact point clearances. 20pc Set (marked in metric sizes only). 0.05mm. -...

Feeler Gauge Set (35-1767)

$7.65

Feeler gauge set with 45 degree ends. Includes Sizes - .008", .010", .012", .013", .014", .015", .016", 018", .019", .020", .025", .026" Marked in...

Heavy Duty Hose Cutter (35-0039)

$16.69

A must-have tool for any serious motorcycle garage. This heavy-duty hose cutter delivers clean cuts every time—no crushed lines, no frayed edges, no rework....

Flywheel Puller ~ 22mm x 1.5 Right Hand Thread (35-0019)

$12.50

Flywheel Puller 22mm x 1.5 Right Hand ThreadInternal Thread Flywheels & Rotors Fits: Husqvarna 1990 & Later WX 2 Cycle Enduro Part Number: 35-0019

25 Feet ~ Safety Wire (35-0087)

$9.64

Stainless Steel Safety Wire - 25 Foot Roll, .032" Diameter. Part Number: 35-0087

Rear Wheel Bearing Retainer Ring Tool (73-0187)

$42.29

Rear Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the rear wheel sprocket hub bearing retainer ring with 1/2 inch...

Front Wheel Bearing Retainer Ring Tool (73-0186)

$32.45

Front Wheel Bearing Retainer Ring Tool. High quality tool for removing and fitting the front wheel bearing retainer ring with 1/2 inch socket bar...

Steering Race Remover 35-55mm (35-9124)

$29.46

Steering Head Bearing Race Remover, Range 35-55mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from...

Steering Race Remover 25-35mm (35-9123)

$29.46

Steering Head Bearing Race Remover, Range 25-35mm ID. This tool will assist in removing motorcycle steering head bearing races. The size range is from...

Fork Cap Wrench ~ 35MM Size (35-9113)

$5.85

Fork Cap Wrench ~ 35MM Size. This is a non-marring fork cap wrench that fits all motorcycles with 35MM fork caps. This wrench will...

Tire Valve Stem Tool (35-9040)

$3.19

Tire Valve Stem Tool Core Removal & Repair ToolPart Number: 35-9040

Timing Light (35-9000)

$42.29

Timing Light Inductive Xenon Timing Light Operates From 12 Volt BatteryPart Number: 35-9000

Scraper Knife (35-8002)

$8.65

Scraper Knife 15mm Stainless SteelPart Number: 35-8002

Sold out

Adjustable Fork Seal Driver 35-45mm (35-3041)

$63.91

Adjustable 35-45mm Fork Seal Driver. This high quality tool can be used on many different fork sizes. Use these for easy installation of most...

Feeler Gauge Set (35-1769)

$15.30

Feeler Gauge Set - Metric/Inch Feeler Gauge Set for setting valve and contact point clearances. 32pc Set (marked in metric and inch sizes). 0.04mm....

Fork Cap Socket Tool (35-1082)

$5.85

19mm Fork Cap Socket Tool, This Tool Is Needed To Loosen Or Remove The Front Fork Cap Bolts On Many BikesPart Number: 35-1082

Chain Puller (35-0130)

$12.77

Chain Puller Pulls Together Chain Ends to Allow Joiner Link To be Slipped Into PlacePart Number: 35-0130

Cam Chain Breaker / Riveter Tool (35-0112)

$86.45

Cam Chain Breaker / Riveter ToolPart Number: 35-0112

Replacement Bit Set (35-0110)

$6.65

Replacement Bit Set 3" Long Driver Bit Set Fits 35-0106 & 35-0095 Impact Drivers Contains 2 Phillips & 2 Slotted BitsPart Number: 35-0110

Spoke Wrench Set (35-0109)

$8.65

Spoke Wrench Set Fits #8/9 & #10/11 ChromePart Number: 35-0109

Stud Extractor 1-6mm (35-0102)

$21.28

Stud Extractor 1/4" Drive, used to remove seized or broken studs and bolts. Designed to fit into small areas, where studs may be hard...

Cylinder Stud Installation Tool Set (35-0101)

$12.77

3 Piece Cylinder Stud Installation Tool Set. Installs studs without damaging the threads. Steel construction with black oxide finish for longer tool life. Includes...

3/8" Drive Click Type Torque Wrench Tool (35-0099)

$48.15

3/8" Drive Window Click Type Torque Wrench Tool with Black Plastic Storage Case. 10-100Ft. Lbs. This click-style torque wrench easily tightens various automotive bolts,...

Rectangular Magnetic Parts Dish (35-0098)

$15.96

Rectangular Stainless Steel Magnetic Parts Dish. Very useful when working with small screws, hardware and parts. 9.5" Length, 5.5" Width, 1.1" Height.Part Number: 35-0098

Tire Pressure Gauge (35-0093)

$6.45

Tire Pressure Gauge Dial Type Measures From 10-60 PSIPart Number: 35-0093

Carburetor Adjusting Tool (35-0084)

$23.28

Carburetor Adjusting Tool. Works with Mikuni or Keihin carbs. 11" long tool with a 8mm hex nut and screwdriver slot adjusting bolt. This combo...

Clutch Center Nut Removal Tool ~ Premium (35-0076)

$23.28

Premium Clutch Center Nut Removal Tool, The perfect tool for easier removal/fitting, without damaging the special locking nut. Both ends with 1/2 drive extension...

Steering Bearing Installation Tool (35-0073)

$54.06

Steering Bearing Installation Tool. Includes one driver and three aluminum adapters. Unique system utilizes specially designed aluminum adaptors to quickly and accurately install nearly...

Chain Alignment Tool (35-0071)

$17.29

Chain Alignment Tool. This tool provides an easy way to verify your chain is aligned properly to the front and rear sprockets after rear...

419pc O-Rings Kit with Plastic Case (35-0067)

$28.93

419pc O-Rings Kit with Plastic Case. 32 different sizes included metric sizes. QTY---Width----Inside Dia.---------QTY---Width-----Inside Dia. 20X---1.50mm--3.00mm------------13X---2.50mm--11.00mm 23X---1.50mm--7.00mm------------14X---2.50mm--13.00mm 23X---1.50mm--10.0mm------------13X---2.50mm--14.00mm 23X---1.50mm--13.0mm------------14X---2.50mm--16.00mm 20X---2.00mm--4.40mm------------14X---2.50mm--18.00mm 18X---2.00mm--5.00mm------------13X---2.50mm--19.00mm 14X---2.50mm--10.0mm------------14X---2.50mm--21.00mm 13X---2.50mm--22.00mm----------10X---3.50mm--31.00mm 10X---3.50mm--18.00mm----------10X---3.50mm--33.00mm...

Customer Login

Tools

My Motorcycle

Categories

World Wide Shipping

Secure Payments

Why Purchase From Us?

Your cart